LQ190E1LW01 Sharp Microelectronics, LQ190E1LW01 Datasheet - Page 32

• Manufacturer Part Number: LQ190E1LW01
• Description: LCD Graphic Display Modules & Accessories 19 SXGA Wide Angle
• Manufacturer: Sharp Microelectronics

Specifications of LQ190E1LW01

• Pixel Density: 1280 x 1024
• Module Size (w X H X T): 104.2 mm x 330 mm x 20 mm
• Viewing Area (w X H): 376.32 mm x 301.056 mm
• Backlighting: Black
• Display Mode: SXGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

B
C
D
A
EDIT DATE
DESIG.
( ( ( ( 3 3 3 3 ) Handling
( ( ( ( 4 4 4 4 ) Precautions in regards of ope
) Handling
) Handling
) Handling of LCD module
) Precautions in regards of ope
) Precautions in regards of ope
) Precautions in regards of operating the LCD module
(Caution) Be careful not to allow the water or solvent to enter the module.
Adhere to the specified power supply sequence.
Adhere to the specified power supply sequence.
Do not operate the LCD module when condensation occurs.
Do not operate
Adhere to the specified power supply sequence.
Adhere to the specified power supply sequence.
Do not operate
Do not operate
Do not place or contact objects on the display surface for a long period of time.
Do not place or contact objects on the display surface for a long period of time.
Do not place or contact objects on the display surface for a long period of time.
Do not place or contact objects on the display surface for a long period of time.
This may make some parts of the LCD module distorted and the quality of display may
deteriorate.
Do not pull the cold
Do not pull the cold- - - - cathode tube cable strongly.
Do not pull the cold
Do not pull the cold
If the cable is pulled with the strength of 2kg or more, the cable may be damaged or may
lose reliability.
Assemble the module into user’s system in a dust free environment.
Assemble the module into user’s system in a dust free environment.
Assemble the module into user’s system in a dust free environment.
Assemble the module into user’s system in a dust free environment.
Conductive foreign matter adheres to the module may cause failures.
Take anti
Take anti
Take anti
Take anti- - - - electrostatic measures for assembling the module.
Since the LCD module contains CMOS-ICs, the following points should be observed.
Do not pull the connecting cable
Do not pull the connecting cable
Do not pull the connecting cable
Do not pull the connecting cable on the rear face of the LCD module strongly.
Do not disassemble or remodel the LCD module.
Do not disassemble or remodel the LCD module.
Do not disassemble or remodel the LCD module.
Do not disassemble or remodel the LCD module.
Disassembly or remodeling of the LCD module may result in malfunctions or deterioration
of the display quality and reliability.
If not followed, the CMOS-IC may cause a latch-up, or DC voltage may be applied to the
liquid crystal, which cause a failure or serious deterioration in display quality.
If the LCD module is operated when condensation is on the terminals of the LCD panel, the
terminals cause electrochemical reaction, and may reach disconnection. Condensation
easily occurs especially when the module is moved from cold environment to warm
environment.
For assembling the module, operator should be grounded and wear cotton or conductive
gloves.
Floor of work area and work table to assemble the LCD module should be covered with
electrostatic shielding in order to discharge static electricity via an earth wire.
If necessary, ground operation tools (soldering iron, radio pliers, tweezers, etc.).
Do not take the module out of the conductive bag until the module is assembled.
Do not assemble the module under low humidity (50%RH or less).
DESIG.
1
1
deformed or discolored.
Wipe off immediately in the same way as for dirt.
of LCD module
of LCD module
of LCD module
CHECK
If saliva or water drops are left for a long period of time, the part may become
Do not allow oil to adhere to the module since excessive oil is hard to clean.
electrostatic measures for assembling the module.
electrostatic measures for assembling the module.
electrostatic measures for assembling the module.
the LCD module when condensation occurs.
the LCD module when condensation occurs.
CHECK
the LCD module when condensation occurs.
APPR.
cathode tube cable strongly.
cathode tube cable strongly.
cathode tube cable strongly.
rating the LCD module
rating the LCD module
rating the LCD module
2
on the rear face of the LCD module strongly.
on the rear face of the LCD module strongly.
on the rear face of the LCD module strongly.
DESCRIPTION
APPR.
TITLE
DRAW. NO
SHARP CORPORATION
SHARP CORPORATION
SHARP CORPORATION
SHARP CORPORATION
3
.
(FLC48SXC8V-11AA)
LQ190E1LW01
L D 1 7 4 4 3
30
/
CUST.
4
A
B
C
D
E
F