TEA1750T/N1/DG,518 NXP Semiconductors, TEA1750T/N1/DG,518 Datasheet - Page 8
![IC PFC CONTROLLER 16SO](/photos/15/59/155975/so-16_sml.jpg)
TEA1750T/N1/DG,518
Manufacturer Part Number
TEA1750T/N1/DG,518
Description
IC PFC CONTROLLER 16SO
Manufacturer
NXP Semiconductors
Series
GreenChip™ IIIr
Datasheet
1.TEA1750TN1518.pdf
(29 pages)
Specifications of TEA1750T/N1/DG,518
Mode
Discontinuous Conduction (DCM)
Frequency - Switching
100kHz ~ 150kHz
Current - Startup
60µA
Mounting Type
Surface Mount
Package / Case
16-SOIC (0.154", 3.90mm Width)
Output Voltage
12 V
Output Current
- 80 uA
Output Power
0.6 W
Duty Cycle (max)
10 %
Input Voltage
70 VAC to 276 VAC
Switching Frequency
125 KHz
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Operating Temperature
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TEA1750T/N1/DG,518
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
TEA1750_2
Product data sheet
7.1.4 Fast latch reset
7.1.5 Overtemperature protection (OTP)
7.2.1 t
7.2.2 Valley switching and demagnetization (PFCAUX pin)
7.2 Power factor correction circuit
In a typical application, the mains can be interrupted briefly to reset the latched protection.
The PFC bus capacitor, C
reset.
Typically the PFC bus capacitor, C
level. When the latched protection is set, the clamping circuit of the VINSENSE circuit is
disabled (see also
750 mV (typ) and then is raised to 870 mV (typ), the latched protection is reset.
The latched protection will also be reset by removing both the voltage on pin V
pin HV.
An accurate internal temperature protection is provided in the circuit. When the junction
temperature exceeds the thermal shutdown temperature, the IC only stops switching. As
long as OTP is active, the V
circuit is supplied from the HV pin if the V
OTP is a latched protection. It can be reset by removing both the voltage on pin V
on pin HV or by the fast latch reset function, see
The power factor correction circuit operates in quasi-resonant or discontinuous conduction
mode with valley switching. The next primary stroke is only started when the previous
secondary stroke has ended and the voltage across the PFC MOSFET has reached a
minimum value. The voltage on the PFCAUX pin is used to detect transformer
demagnetization and the minimum voltage across the external PFC MOSFET switch.
The power factor correction circuit is operated in t
reduction of a typical application is well within the class-D requirements.
The PFC MOSFET is switched on after the transformer is demagnetized. Internal circuitry
connected to the PFCAUX pin detects the end of the secondary stroke. It also detects the
voltage across the PFC MOSFET. The next stroke is started if the voltage across the PFC
MOSFET is at its minimum in order to reduce switching losses and electromagnetic
interference (EMI) (valley switching).
If no demagnetization signal is detected on the PFCAUX pin, the controller generates a
zero current signal (ZCS), 50 s (typ) after the last PFC gate signal.
If no valley signal is detected on the PFCAUX pin, the controller generates a valley signal
4 s (typ) after demagnetization was detected.
To protect the internal circuitry, for example during lightning events, it is advisable to add
a 5 k series resistor to this pin. To prevent incorrect switching due to external
disturbance, the resistor should be placed close to the IC on the printed circuit board.
on
control
Section
Rev. 02 — 15 December 2008
bus
7.2.8). As soon as the VINSENSE voltage drops below
CC
, does not have to discharge for this latched protection to
capacitor is not recharged from the HV mains. The OTP
bus
, has to discharge for the V
CC
supply voltage is not sufficient.
Section 7.1.4
on
control. The resulting mains harmonic
GreenChip III SMPS control IC
CC
to drop to this reset
TEA1750
© NXP B.V. 2008. All rights reserved.
CC
and on
CC
8 of 29
and