71M6512-DB Maxim Integrated Products, 71M6512-DB Datasheet - Page 65
71M6512-DB
Manufacturer Part Number
71M6512-DB
Description
Power Management Modules & Development Tools 71M6512 DEMO BOARD 71M6512 DEMO BOARD
Manufacturer
Maxim Integrated Products
Datasheet
1.71M6521DE-DB.pdf
(138 pages)
- Current page: 65 of 138
- Download datasheet (2Mb)
71M652X Software User’s Guide
Notes:
Battery Test
The battery test is based on sampling the voltage applied to the VBAT pin during an alternative multiplexer cycle. The
function used for calculating the battery voltage from the count obtained from the ADC is int32_t mVBat (int32_t v).
In this function, the ADC sample count is shifted right 9 bits (to account for the left-shift operation automatically done by
the ADC). The measured value is not very accurate, since the chip-to-chip variations in offset and LSB resolution are
not calibrated (these may have 5% variations).
The routine battest_start() may be invoked from the command line interface. battest_start() sets the variable
bat_sample_cnt to 2. This signals to the XFER_BUSY interrupt (in ce.c) to take two measurement (to account for the
variations caused by the amplifier chopping). The RTC date is recorded in the structure last_day. That way, an
automated battery test is run only once per day (when the date changes right after midnight).
The routine battest_run (void) is called from the part of meter_run() that only operates when the CE is active. This is
because the battery test can only run when the CE is active. The routine battest_run (void) compares the current date
with last_day. If it detects a difference, indicating that the date has just changed), it calls battest_start ().
Revision 1.7
•
•
•
•
•
•
For larger EEPROMs, 1010xxR can be the first command (R=1 for read, R = 0 for write operation).
The START command should be sent to the EEPROM before any read or write operation
The algorithms cover single and multi-byte operations limited to a single page.
EEPROMs are organized in pages. In general, ATMEL EEPROMs have 1Kbyte per page (256 x 32 bits).
When reading, no special requirements with respect to page boundaries apply.
Special precautions apply when a page boundary is crossed for write operations: When the end of a page is
reached, the write.to the next page has to be preceded by a START command.
EEPROMs typically respond to START commands with 5ms delay.
EECTRL = 0x05 (stop command)
Clear all registers
© Copyright 2005-2007 TERIDIAN Semiconductor Corporation
count==0?
Start
End
Figure 5-20: Multi-Byte Write
TERIDIAN Proprietary
NO
EECTRL = 0x03 (multiple write with ACK command)
EEDATA= *(destination++)
interrupt rcvd?
count- -
(INT5)
65 of 138
Related parts for 71M6512-DB
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Current & Power Monitors & Regulators Residential Meter Extended Io
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Current & Power Monitors & Regulators Gang Programmer Base Unit+6512 Socket Brd
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Current & Power Monitors & Regulators Residential Meter Extended Io
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products