ATA6603-EK Atmel, ATA6603-EK Datasheet - Page 319

• Manufacturer Part Number: ATA6603-EK
• Description: MCU, MPU & DSP Development Tools Demoboard LIN-MCM
• Manufacturer: Atmel

Specifications of ATA6603-EK

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.25.2
T
Notes:
4921E–AUTO–09/09
Symbol
I
V
I
t
CC
ACLK
ACID
case
ACIO
= -40°C to +125°C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at V
4. Although each I/O port can source more than the test conditions (20mA at V
5. All DC Characteristics contained in this datasheet are based on actual ATA6602 microcontrollers characterization.
6. Values with “Power Reduction REgister - PRR” enabled (0xEF).
DC Characteristics (Continued)
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
conditions (non-transient), the following must be observed:
ATA6602/ATA6603:
1] The sum of all IOL, for ports C0 - C5, should not exceed 100 mA.
2] The sum of all IOL, for ports C6, D0 - D4, should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
ATA6602/ATA6603:
1] The sum of all IOH, for ports C0 - C5, should not exceed 100 mA.
2] The sum of all IOH, for ports C6, D0 - D4, should not exceed 100 mA.
3] The sum of all IOH, for ports B0 - B7, D5 - D7, should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
CC
= 2.7V to 5.5V (unless otherwise noted)
(6)
Condition
Active 4MHz, V
(ATA6602/ATA6603L)
Active 8MHz, V
(ATA6602/ATA6603)
Active 15MHz, V
(ATA6602/ATA6603)
Idle 4MHz, V
(ATA6602/ATA6603V)
Idle 8MHz, V
(ATA6602/ATA6603L)
Idle 15MHz, V
(ATA6602/ATA6603)
WDT enabled, V
WDT enabled, V
WDT disabled, V
WDT disabled, V
V
V
V
V
V
CC
in
CC
in
CC
= V
= V
= 5V
= 5V
= 4.5V
CC
CC
/2
/2
CC
CC
CC
CC
CC
= 3V
= 5V
CC
CC
CC
CC
CC
= 5V
= 3V
= 5V
= 5V
= 3V
= 5V
= 3V
= 5V
Min.
-50
(5)
CC
CC
= 5V, 10mA at V
= 5V, 10mA at V
Typ.
10.0
12.6
140
1.8
6.0
0.4
1.4
2.8
6.6
10
8
5
ATA6602/ATA6603
CC
Max.
CC
= 3V) under steady state
3.0
2.4
10
16
30
50
24
36
40
50
1
4
= 3V) under steady state
(5)
Units
mA
mA
mA
mA
mA
mA
mV
µA
µA
µA
µA
nA
ns
319