ADF7020-1BCPZ-RL7 Analog Devices Inc, ADF7020-1BCPZ-RL7 Datasheet - Page 5

• Manufacturer Part Number: ADF7020-1BCPZ-RL7
• Description: IC,RF Modulator/Demodulator,LLCC,48PIN,PLASTIC
• Manufacturer: Analog Devices Inc

Specifications of ADF7020-1BCPZ-RL7

• Design Resources: Low power, Long Range, ISM Wireless Measuring Node (CN0164)
• Frequency: 431MHz ~ 478MHz and 862MHz ~ 956MHz
• Data Rate - Maximum: 200kbps
• Modulation Or Protocol: ASK, FSK
• Applications: Data Transfer, RKE, Remote Control/Security Systems
• Power - Output: -16dBm ~ 13dBm
• Sensitivity: -119dBm
• Voltage - Supply: 2.3 V ~ 3.6 V
• Current - Receiving: 17.6mA
• Current - Transmitting: 21mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LFCSP
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 7mm
• Product Length (mm): 7mm
• Operating Supply Voltage (min): 2.3V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF7020-1DBZ8 - BOARD EVAL ADF7020-1 128-142MHZEVAL-ADF7020-1DBZ7 - BOARD EVAL ADF7020-1 310-340MHZEVAL-ADF7020-1DBZ6 - BOARD EVAL ADF7020-1 470-510MHZEVAL-ADF7020-1DBZ4 - BOARD EVAL ADF7020-1 405-435MHZEVAL-ADF7020-1DBZ5 - BOARD EVAL ADF7020-2 ADJ FREQ
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant

Parameter
RECEIVER PARAMETERS
CHANNEL FILTERING
CO-CHANNEL REJECTION
BLOCKING
FSK/GFSK Input Sensitivity
OOK Input Sensitivity
LNA and Mixer, Input IP3
Rx Spurious Emissions
AFC
Adjacent Channel Rejection
Second Adjacent Channel Rejection
Third Adjacent Channel Rejection
Image Channel Rejection
Wideband Interference Rejection
±1 MHz
±5 MHz
±10 MHz
±10 MHz (High Linearity Mode)
Saturation (Maximum Input Level)
LNA Input Impedance
RSSI
Sensitivity at 1 kbps
Sensitivity at 9.6 kbps
Sensitivity at 1 kbps
Sensitivity at 9.6 kbps
Enhanced Linearity Mode
Low Current Mode
High Sensitivity Mode
Pull-In Range
Response Time
Accuracy
(Offset = ±1 × IF Filter BW
Setting)
(Offset = ±2 × IF Filter BW
Setting)
(Offset = ±3 × IF Filter BW
Setting)
Range at Input
Linearity
Absolute Accuracy
Response Time
8
7
Min
Typ
−119.2
−114.2
−118.2
−111.8
6.8
−3.2
−35
±50
48
1
27
50
55
35
−2
70
60
68
65
72
12
237 − j193
101.4 − j161.6
49.3 − j104.6
−100 to −36
±2
±3
150
Rev. 0 | Page 5 of 48
Max
−57
−47
dBm
Unit
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm
kHz
Bits
kHz
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
Ω
Ω
Ω
dBm
dB
dB
μs
Test Conditions
At BER = 1E − 3, FRF = 315 MHz,
LNA and PA matched separately
FDEV= 5 kHz, high sensitivity mode
FDEV = 10 kHz, high sensitivity mode
At BER = 1E − 3, FRF = 315 MHz
High sensitivity mode
High sensitivity mode
Pin = −20 dBm, 2 CW interferers,
FRF = 315 MHz, F1 = FRF + 3 MHz,
F2 = FRF + 6 MHz, maximum gain
<1 GHz at antenna input
>1 GHz at antenna input
IF_BW = 200 kHz
Modulation index = 0.875
IF filter BW settings = 100 kHz, 150 kHz,
200 kHz; desired signal 3 dB above the input
sensitivity level; CW interferer power level
increased until BER = 10
excluded
Image at FRF − 400 kHz
Swept from 100 MHz to 2 GHz, measured as
channel rejection
Desired signal 3 dB above the input sensitivity
level, CW interferer power level increased
until BER = 10
FSK mode, BER = 10
FRF = 130 MHz, RFIN to GND
FRF = 310 MHz
FRF = 610 MHz
See the RSSI/AGC section
−2
−3
−3
; image channel
ADF7020-1
6
7