CY8C3246PVI-141 Cypress Semiconductor Corp, CY8C3246PVI-141 Datasheet - Page 49

• Manufacturer Part Number: CY8C3246PVI-141
• Description: CY8C3246PVI-141
• Manufacturer: Cypress Semiconductor Corp
• Series: PSOC™ 3 CY8C32xxr

Specifications of CY8C3246PVI-141

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, I²C, LIN, SPI, UART/USART
• Peripherals: CapSense, DMA, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.71 V ~ 5.5 V
• Data Converters: A/D 2x12b, D/A 1x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7.5 USB
PSoC includes a dedicated Full-Speed (12 Mbps) USB 2.0
transceiver supporting all four USB transfer types: control,
interrupt, bulk, and isochronous. PSoC Creator provides full
configuration support. USB interfaces to hosts through two
dedicated USBIO pins, which are detailed in the
Routing”
USB includes the following features:
Figure 7-18. USB
7.6 Timers, Counters, and PWMs
The Timer/Counter/PWM peripheral is a 16-bit dedicated
peripheral providing three of the most common embedded
peripheral features. As almost all embedded systems use some
combination of timers, counters, and PWMs. Four of them have
been included on this PSoC device family. Additional and more
advanced functionality timers, counters, and PWMs can also be
instantiated in Universal Digital Blocks (UDBs) as required.
PSoC Creator allows you to choose the timer, counter, and PWM
features that they require. The tool set utilizes the most optimal
resources available.
The Timer/Counter/PWM peripheral can select from multiple
clock sources, with input and output signals connected through
the DSI routing. DSI routing allows input and output connections
Document Number: 001-56955 Rev. *J
Eight unidirectional data endpoints
One bidirectional control endpoint 0 (EP0)
Shared 512-byte buffer for the eight data endpoints
Dedicated 8-byte buffer for EP0
Three memory modes
Internal 3.3 V regulator for transceiver
Internal 48 MHz main oscillator mode that auto locks to USB
bus clock, requiring no external crystal for USB (USB equipped
parts only)
Interrupts on bus and each endpoint event, with device wakeup
USB Reset, Suspend, and Resume operations
Bus powered and self powered modes
Interrupts
Manual Memory Management with No DMA Access
Manual Memory Management with Manual DMA Access
Automatic Memory Management with Automatic DMA
Access
(Serial Interface
section on page 34.
Engine)
48 MHz
Arbiter
S I E
IMO
512 X 8
SRAM
USB
I/O
D+
D–
External 22 Ω
Resistors
“I/O System and
to any device pin and any internal digital signal accessible
through the DSI. Each of the four instances has a compare
output, terminal count output (optional complementary compare
output), and programmable interrupt request line. The
Timer/Counter/PWMs are configurable as free running, one shot,
or Enable input controlled. The peripheral has timer reset and
capture inputs, and a kill input for control of the comparator
outputs. The peripheral supports full 16-bit capture.
Timer/Counter/PWM features include:
Figure 7-19. Timer/Counter/PWM
7.7 I
The I
designed to interface the PSoC device with a two wire I
communication bus. The bus is compliant with Philips ‘The I
Specification’ version 2.1. Additional I
instantiated using Universal Digital Blocks (UDBs) in PSoC
Creator, as required.
To eliminate the need for excessive CPU intervention and
overhead, I
and generation of framing bits. I
or multimaster (Slave and Master). In slave mode, the unit
always listens for a start condition to begin sending or receiving
data. Master mode supplies the ability to generate the Start and
Stop conditions and initiate transactions. Multimaster mode
provides clock synchronization and arbitration to allow multiple
masters on the same bus. If Master mode is enabled and Slave
mode is not enabled, the block does not generate interrupts on
externally generated Start conditions. I
DSI routing and allows direct connections to any GPIO or SIO
pins.
Clock
Reset
Enable
Capture
Kill
16-bit Timer/Counter/PWM (down count only)
Selectable clock source
PWM comparator (configurable for LT, LTE, EQ, GTE, GT)
Period reload on start, reset, and terminal count
Interrupt on terminal count, compare true, or capture
Dynamic counter reads
Timer capture mode
Count while enable signal is asserted mode
Free run mode
One Shot mode (stop at end of period)
Complementary PWM outputs with deadband
PWM output kill
2
2
C peripheral provides a synchronous two wire interface
C
2
C specific support is provided for status detection
Timer / Counter /
PWM 16-bit
PSoC
®
2
C operates as a slave, a master,
3: CY8C32 Family
2
2
C interfaces can be
C interfaces through the
IRQ
TC / Compare!
Compare
Data Sheet
Page 49 of 119
2
C serial
2
C
[+] Feedback