CYII5SC1300AB-QDC Cypress Semiconductor Corp, CYII5SC1300AB-QDC Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CYII5SC1300AB-QDC
Manufacturer Part Number
CYII5SC1300AB-QDC
Description
SENSOR IMAGE COLOR CMOS 84-LCC
Manufacturer
Cypress Semiconductor Corp
Type
CMOS Imagingr
Specifications of CYII5SC1300AB-QDC
Pixel Size
6.7µm x 6.7µm
Active Pixel Array
1280H x 1024V
Frames Per Second
27
Voltage - Supply
3 V ~ 4.5 V
Package / Case
84-LCC
Sensor Image Color Type
Color
Sensor Image Size Range
>= 480,000Pixels
Sensor Image Size
1280x1024Pixels
Operating Supply Voltage (min)
3V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
0C to 65C
Package Type
CLCC
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
84
Package
84CLCC
Image Size
1280x1024 Pixels
Color Sensing
Color
Operating Temperature
0 to 65 °C
Operating Supply Voltage
3 to 3.6 V
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Image Core Operation
Image Core Operation and Signalling
Figure 8
sub-sampling and column/row swapping circuits. Most of the
signals involved are not available from the outside because they
are generated by the X-sequencer and SS-sequencer blocks.
The integration of the pixels is controlled by internal signals such
as reset, sample, and hold which are generated by the on-chip
SS-sequencer that is controlled with the external signals
SS_START and SS_STOP. Reading out the pixel array starts by
applying a Y_START together with a Y_CLOCK signal; internally
this is followed by a calibration sequence to calibrate the output
amplifiers (during the row blanking time). Signals necessary to
do this calibration are generated by the on-chip X-sequencer.
This calibration sequence takes typically 3.5 μs and is necessary
to remove ‘Fixed Pattern Noise’ of the pixels and of the column
amplifiers themselves by means of a double sampling technique.
After the row blanking time, the pixels are fed to the output
amplifier. The pixel rate is equal to the SYS_CLOCK frequency.
Document #: 38-05710 Rev. *H
is a functional representation of the image core without
VDDR_LEFT
SYS_CLOCK
Y_CLOCK
Y_START
VDDH
Y-left addressing
BUS_A
BUS_B
Read-pointer
Pixel column
Figure 8. Image Core
X addressing
Pixel
SAMPLE
A
RESET
HOLD
Pixel
Image Core Supply Considerations
The image sensor has several supply voltages:
VDDH is the voltage that controls the sample switches. Do not
apply a higher voltage than this to the chip.
The VDDR_LEFT voltage is the highest (nominal) reset voltage
of the pixel core.
The VDDR_RIGHT voltage is generated from the VDDR_LEFT
voltage using a circuit that is programmed with the
KNEEPOINT_LSB/MSB bits in the sequencer register (see also
Pixel reset knee-point for multiple slope operation (bits 8, 9, and
10)
the circuit and apply an external voltage to supply the multiple
slope reset voltage by setting the VDDR_RIGHT_EXT bit in the
SEQUENCER register. When no external voltage is applied
(recommended), connect the VDDR_RIGHT pin to a capacitor
(recommended value = 1µF). VDDC is the pixel core supply.
VDDA is the image core and periphery analog supply. VDDD is
the image core and periphery digital supply.
Note that the IBIS5-B-1300 image sensor has no on-chip power
rejection circuitry. As a consequence all variations on the analog
supply voltages can contribute to random variations (noise) on
the analog pixel signal, which is seen as random noise in the
image. During the camera design, take precautions to supply the
sensor with very stable supply voltages to avoid this additional
noise. The pixel array (VDDR_LEFT, VDDH and VDDC) analog
supplies are especially vulnerable to this.
B
Pixel row
on page 17). You can disconnect the VDDR_RIGHT pin from
Column amplifiers
Output amplifier
Y-right addressing
Y_START
Y_CLOCK
PXL_OUT
Vddreset
VDDR_RIGHT
VDDC
CYII5SM1300AB
Page 9 of 35
[+] Feedback