12065E104ZAT2A AVX Corporation, 12065E104ZAT2A Datasheet - Page 28

• Manufacturer Part Number: 12065E104ZAT2A
• Description: Cap Ceramic 0.1uF 50VDC Z5U -20% to 80% SMD 1206 Paper T/R
• Manufacturer: AVX Corporation
• Type: Flatr
• Series: 1206r

Specifications of 12065E104ZAT2A

• Package/case: 1206
• Mounting: Surface Mount
• Capacitance Value: 0.1 uF
• Dielectric: Z5U
• Voltage: 50 Vdc
• Product Length: 3.2 mm
• Product Height: 1.5(Max) mm
• Product Depth: 1.6 mm
• Tolerance: -20 to 80 %
• Dielectric Characteristic: Z5U
• Capacitance: 0.1µF
• Capacitance Tolerance: +80, -20%
• Voltage Rating: 50VDC
• Capacitor Case Style: 1206
• No. Of Pins: 2
• Capacitor Mounting: SMD
• Rohs Compliant: Yes
• Case Code: 1206
• Case Size: 1206
• Material, Element: Ceramic
• Termination: SMT
• Operating Temperature Range: + 10 C to + 85 C
• Temperature Coefficient / Code: Z5U
• Package / Case: 1206 (3216 metric)
• Product: General Type MLCCs
• Dimensions: 1.6 mm (0.063 in) W x 3.2 mm (0.126 in) L
• Dissipation Factor Df: 4
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: RoHS Compliant part

RESISTANCE TO VIBRATION
General Specifications
Mechanical
Specification
Measuring Conditions
Specification
Measuring Conditions
SOLDERABILITY
END TERMINATION ADHERENCE
Specification
Measuring Conditions
No evidence of peeling of end terminal
After soldering devices to circuit board apply 5N
(0.51kg f) for 10 ± 1 seconds, please refer to Figure 1.
fresh solder
Dip device in eutectic solder at 230 ± 5°C for
2 ± .5 seconds
Appearance:
No visual defects
Capacitance
Within specified tolerance
Q, Tan Delta
To meet initial requirement
Insulation Resistance
C0G (NP0), X7R
Z5U, Y5V
Vibration Frequency
10-2000 Hz
Maximum Acceleration
20G
Swing Width
1.5mm
Test Time
X, Y, Z axis for 2 hours each, total 6 hours of test
TEST BOARD
95% of each termination end should be covered with
5N FORCE
Initial Value x 0.1
DEVICE UNDER TEST
Initial Value x 0.3
Terminal Adhesion
Figure 1.
BEND STRENGTH
RESISTANCE TO SOLDER HEAT
Specification
Measuring Conditions
Specification
Measuring Conditions
Deflection
Appearance:
No visual defects
Capacitance Variation
Insulation Resistance
Please refer to Figure 2
Deflection:
2mm
Test Time:
30 seconds
Appearance:
No serious defects, <25% leaching of either end
terminal
Capacitance Variation
Q, Tan Delta
To meet initial requirement
Insulation Resistance
To meet initial requirement
Dielectric Strength
No problem observed
Dip device in eutectic solder at 260°C, for 1 minute.
Store at room temperature for 48 hours (24 hours for
C0G (NP0)) before measuring electrical parameters.
Part sizes larger than 3.20mm x 2.49mm are reheated
at 150°C for 30 ±5 seconds before performing test.
C0G (NP0): ± 2.5% or ± 2.5pF, whichever is greater
C0G (NP0): ± 5% or ± .5pF, whichever is larger
C0G (NP0): ≥ Initial Value x 0.3
2mm
X7R: ≤ ± 7.5%
Z5U: ≤ ± 20%
X7R: ≤ ± 12%
Z5U: ≤ ± 30%
X7R: ≥ Initial Value x 0.3
Z5U: ≥ Initial Value x 0.1
Y5V: ≤ ± 20%
Y5V: ≤ ± 30%
Y5V: ≥ Initial Value x 0.1
45mm
Figure 2. Bend Strength
Speed = 1mm/sec
45mm
R340mm
Supports
27