PRIXP422ABB Intel, PRIXP422ABB Datasheet - Page 125

• Manufacturer Part Number: PRIXP422ABB
• Description: Network Proc 1.3V/3.3V 266MHz 492-Pin BGA
• Manufacturer: Intel

Specifications of PRIXP422ABB

• Package: 492BGA
• Core Operating Frequency: 266 MHz
• Operating Supply Voltage: 1.3|3.3 V
• Package Type: BGA
• Pin Count: 492
• Mounting: Surface Mount
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Lead Free Status / Rohs Status: Compliant

Datasheet—Intel
Table 68.
5.6
June 2007
Document Number:
Reset Timings Table Parameters
Power Sequence
The 3.3-V I/O voltage (V
processor voltage (V
processors’ voltage (V
(V
V
1
There are no power-down requirements for the IXP42X product line and IXC1100
control plane processors.
®
T
T
T
T
T
T
Notes:
1.
2.
3.
RELEASE_PWRON_RST_N
RELEASE_RESET_IN_N
PLL_LOCK
EX_ADDR_SETUP
EX_ADDR_HOLD
WARM_RESET
CCOSCP
252479-007US
IXP42X product line and IXC1100 control plane processors
µ
CCP
s. The T
). The V
Symbol
T
The expansion bus address is captured as a derivative of the RESET_IN_N signal going high. When a
programmable-logic device is used to drive the EX_ADDR signals instead of pull-downs, the signals
must be active until PLL_LOCK goes high.
PLL_LOCK is deasserted immediately when watchdog timer event occurs, or when RESET_IN_N is
asserted, or when PWRON_RST_N is asserted. PLL_LOCK remains deasserted for ~24 ref_clocks after
the watchdog reset is deasserted (internal to the chip). A ref clock time period is 1/CLKIN.
RELEASE_PWRON_RST_N
follows the V
POWER_UP
CCOSC
Intel
, V
timing parameter is measured from V
Minimum time required to hold the
PWRON_RST_N at logic 0 state after
stable power has been applied to the
IXP42X product line and IXC1100 control
plane processors.
Minimum time required to hold the
RESET_IN_N at logic 0 state after
PWRON_RST_N has been released to a
logic 1 state. The RESET_IN_N signal
must be held low when the
PWRON_RST_N signal is held low.
Maximum time for PLL_LOCK signal to
drive to logic 1 after RESET_IN_N is
driven to logic 1 state. The boot
sequence does not occur until this period
is complete.
Minimum time for the EX_ADDR signals
to drive the inputs prior to RESET_IN_N
being driven to logic 1 state. This is used
for sampling configuration information.
Minimum/maximum time for the
EX_ADDR signals to drive the inputs prior
to PLL_LOCK being driven to logic 1
state. This is used for sampling
configuration information.
Minimum time required to drive
RESET_IN_N signal to logic 0 in order to
cause a Warm Reset in the IXP42X
product line and IXC1100 control plane
processors
supply must not be disturbed and
PWRON_RST_N signal must remain at
logic high during the entire process.
CC
CCP
CCPLL1
CC
®
). The IXP42X product line and IXC1100 control plane
IXP42X Product Line of Network Processors and IXC1100 Control Plane Processor
) must never become stable prior to the 3.3-V I/O voltage
is the time required for the internal oscillator to reach stability.
CCP
power-up pattern. The value for T
, and V
) must be powered up 1
.
During this period, the power
Parameter
CCPLL2
voltages follow the V
µs
2000
Min.
500
before the Intel XScale
10
50
0
CCP
POWER_UP
Typ.
at 3.3 V and V
CC
power-up pattern. The
Max.
10
20
must be at least
Units
CC
ns
ns
µs
ns
ns
ns
®
at 1.3 V.
Datasheet
Note
1
2
2
125