MT48LC4M16A2P-75:G Micron Technology Inc, MT48LC4M16A2P-75:G Datasheet - Page 43

• Manufacturer Part Number: MT48LC4M16A2P-75:G
• Description: DRAM Chip SDRAM 64M-Bit 4Mx16 3.3V 54-Pin TSOP-II Tray
• Manufacturer: Micron Technology Inc
• Type: SDRAMr
• Series: -r

Specifications of MT48LC4M16A2P-75:G

• Density: 64 Mb
• Maximum Clock Rate: 133 MHz
• Package: 54TSOP-II
• Address Bus Width: 14 Bit
• Operating Supply Voltage: 3.3 V
• Maximum Random Access Time: 6|5.4 ns
• Operating Temperature: 0 to 70 °C
• Organization: 4Mx16
• Address Bus: 14b
• Access Time (max): 6/5.4ns
• Operating Supply Voltage (typ): 3.3V
• Package Type: TSOP-II
• Operating Temp Range: 0C to 70C
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Supply Current: 140mA
• Pin Count: 54
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Format - Memory: RAM
• Memory Type: SDRAM
• Memory Size: 64M (4M x 16)
• Speed: 133MHz
• Interface: Parallel
• Voltage - Supply: 3 V ~ 3.6 V
• Package / Case: 54-TSOP (0.400", 10.16mm Width)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PDF: 09005aef80725c0b/Source: 09005aef806fc13c
64MSDRAM_2.fm - Rev. N 12/08 EN
10. For a READ without auto precharge interrupted by a READ (with or without auto pre-
11. For a READ without auto precharge interrupted by a WRITE (with or without auto pre-
12. For a WRITE without auto precharge interrupted by a READ (with or without auto pre-
13. For a WRITE without auto precharge interrupted by a WRITE (with or without auto pre-
14. For a READ with auto precharge interrupted by a READ (with or without auto precharge),
15. For a READ with auto precharge interrupted by a WRITE (with or without auto precharge),
16. For a WRITE with auto precharge interrupted by a READ (with or without auto precharge),
17. For a WRITE with auto precharge interrupted by a WRITE (with or without auto precharge),
6. All states and sequences not shown are illegal or reserved.
7. READs or WRITEs to bank m listed in the Command (Action) column include READs or
8. Concurrent Auto precharge: Bank n will initiate the auto precharge command when its
9. Burst in bank n continues as initiated.
WRITEs with auto precharge enabled and READs or WRITEs with auto precharge disabled.
burst has been interrupted by bank m’s burst.
charge), the READ to bank m will interrupt the READ on bank n, CL later (Figure 12 on
page 25).
charge), the WRITE to bank m will interrupt the READ on bank n when registered
(Figures 14 and 15 on page 27). DQM should be used one clock prior to the WRITE com-
mand to prevent bus contention.
charge), the READ to bank m will interrupt the WRITE on bank n when registered (Figure 22
on page 32), with the data-out appearing CL later. The last valid WRITE to bank n will be
data-in registered one clock prior to the READ to bank m.
charge), the WRITE to bank m will interrupt the WRITE on bank n when registered
(Figure 20 on page 31). The last valid WRITE to bank n will be data-in registered one clock
prior to the READ to bank m.
the READ to bank m will interrupt the READ on bank n, CL later. The precharge to bank n
will begin when the READ to bank m is registered (Figure 29 on page 37).
the WRITE to bank m will interrupt the READ on bank n when registered. DQM should be
used two clocks prior to the WRITE command to prevent bus contention. The precharge to
bank n will begin when the WRITE to bank m is registered (Figure 30 on page 38).
the READ to bank m will interrupt the WRITE on bank n when registered, with the data-out
appearing CL later. The precharge to bank n will begin after
when the READ to bank m is registered. The last valid WRITE to bank n will be data-in regis-
tered one clock prior to the READ to bank m (Figure 31 on page 38).
the WRITE to bank m will interrupt the WRITE on bank n when registered. The precharge to
bank n will begin after
tered. The last valid WRITE to bank n will be data registered one clock prior to the WRITE to
bank m (Figure 32 on page 39).
t
WR is met, where
43
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
WR begins when the WRITE to bank m is regis-
64Mb: x4, x8, x16 SDRAM
t
WR is met, where
©2000 Micron Technology, Inc. All rights reserved.
Commands
t
WR begins