107314676 Lineage Power, 107314676 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/387/lineage_power_sml.jpg)
107314676
Manufacturer Part Number
107314676
Description
Module DC-DC 1-OUT 15V 3.33A 50W 9-Pin
Manufacturer
Lineage Power
Type
Step Downr
Datasheet
1.JC050C1.pdf
(16 pages)
Specifications of 107314676
Output Current
3.33 A
Output Voltage
15 V
Input Voltage
28 V
Number Of Outputs
1
Output Power
50 W
JC050C, JC075C, JC100C Power Modules: dc-dc Converters;
18 Vdc to 36 Vdc Input, 15 Vdc Output; 50 W to 100 W
8 8
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test configuration in Figure 11, a 33 µF
electrolytic capacitor (ESR < 0.7 Ω at 100 kHz)
mounted close to the power module helps ensure sta-
bility of the unit. For other highly inductive source
impedances, consult the factory for further application
guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL-1950, CSA 22.2-950, and EN60950.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements.
If the input meets extra-low voltage (ELV) require-
ments, then the converter’s output is considered ELV.
The input to these units is to be provided with a maxi-
mum 20 A normal-blow fuse in the ungrounded lead.
Electrical Descriptions
Current Limit
To provide protection in a fault (output overload) condi-
tion, the unit is equipped with internal current-limiting
circuitry and can endure current limiting for an unlim-
ited duration. At the point of current-limit inception, the
unit shifts from voltage control to current control. If the
output voltage is pulled very low during a severe fault,
the current-limit circuit can exhibit either foldback or tai-
lout characteristics (output current decrease or
increase). The unit operates normally once the output
current is brought back into its specified range.
Feature Descriptions
Remote On/Off
Two remote on/off options are available. Positive logic
remote on/off turns the module on during a logic-high
voltage on the ON/OFF pin, and off during a logic low.
Negative logic remote on/off turns the module off dur-
ing a logic high and on during a logic low. Negative
logic (code suffix “1”) is the factory-preferred configura-
tion.
To turn the power module on and off, the user must
supply a switch to control the voltage between the
on/off terminal and the V
switch can be an open collector or equivalent (see
Figure 14). A logic low is V
imum I
should maintain a logic-low voltage while sinking 1 mA.
During a logic high, the maximum V
the power module is 15 V. The maximum allowable
leakage current of the switch at V
If not using the remote on/off feature, do one of the fol-
lowing:
n
n
Remote Sense
Remote sense minimizes the effects of distribution
losses by regulating the voltage at the remote-sense
connections. The voltage between the remote-sense
pins and the output terminals must not exceed the out-
put voltage sense range given in the Feature Specifica-
tions table, i.e.:
The voltage between the V
must not exceed 5.9 V. This limit includes any increase
in voltage due to remote-sense compensation and out-
put voltage set-point adjustment (trim), see Figure 15.
If not using the remote-sense feature to regulate the
output at the point of load, then connect SENSE(+) to
V
O
For negative logic, short ON/OFF pin to V
For positive logic, leave ON/OFF pin open.
(+) and SENSE(-) to V
[V
Figure 14. Remote On/Off Implementation
O
on/off
(+) – V
V
I
on/off
on/off
+
–
during a logic low is 1 mA. The switch
O
(–)] – [SENSE(+) – SENSE(–)] ≤ 1.2 V
ON/OFF
V
V
I
I
(+)
(–)
I
(-) terminal (V
O
(-) at the module.
on/off
O
(+) and V
SENSE(+)
SENSE(–)
= 0 V to 1.2 V. The max-
Lineage Power
March 2008
Data Sheet
on/off
V
V
O
O
on/off
(+)
(–)
O
= 15 V is 50 μA.
on/off
(–) terminals
generated by
). The
I
(-)
8-720 (C).c
LOAD