KSZ8993MLI Micrel Inc, KSZ8993MLI Datasheet - Page 12

• Manufacturer Part Number: KSZ8993MLI
• Description: 2+1 Port 10/100 Switch W/Tranceivers & Frame Buffers, 128-Ld PQFP( , I-Temp)
• Manufacturer: Micrel Inc

Specifications of KSZ8993MLI

• Number Of Primary Switch Ports: 3
• Internal Memory Buffer Size: 32
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 1.89/3.465V
• Operating Supply Voltage (min): 1.71/3.135V
• Power Dissipation: 800mW
• Operating Temperature Classification: Industrial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Supplier Unconfirmed
• Other names: 576-3350

Micrel, Inc.
October 2008
Note:
1. P = Power supply.
Pin Number
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Ipd = Input w/ internal pull-down.
Gnd = Ground.
I = Input.
O = Output.
Ipu = Input w/ internal pull-up.
Pin Name
NC
HWPOVR
P2MDIXDIS
P2MDIX
P1ANEN
P1SPD
P1DPX
P1FFC
NC
NC
PWRDN
AGND
VDDA
AGND
MUX1
MUX2
AGND
VDDA
FXSD1
Type
O
Ipd
Ipd
Ipd
Ipu
Ipd
Ipd
Ipd
Ipd
Ipd
Ipu
Gnd
P
Gnd
I
I
Gnd
P
I
(1)
12
Description
No connect
Hardware pin overwrite
0 = Disable. All strap-in pins configurations are overwritten by
the EEPROM configuration data
1 = Enable. All strap-in pins configurations are overwritten by
the EEPROM configuration data, except for register 0x2C bits
[7:5], (port 2: auto-negotiation enable, force speed, force
duplex).
Port 2 Auto MDI/MDI-X
PD (default) = enable
PU = disable
Port 2 MDI/MDI-X setting when auto MDI/MDI-X is disabled.
PD (default) = MDI-X (transmit on TXP2 / TXM2 pins)
PU = MDI, (transmit on RXP2 / RXM2 pins)
1 = enable auto negotiation on port 1
0 = disable auto negotiation on port 1
1 = force port 1 to 100BT if P1ANEN = 0
0 = force port 1 to 10BT if P1ANEN = 0
1 = port 1 default to full duplex mode if P1ANEN = 1 and auto
negotiation fails. Force port 1 in full-duplex mode if P1ANEN
= 0.
0 = port 1 default to half duplex mode if P1ANEN = 1 and auto
negotiation fails. Force port 1 in half duplex mode if P1ANEN
= 0.
1 = always enable (force) port 1 flow control feature
0 = port 1 flow control feature enable is determined by auto
negotiation result.
No connect
No connect
Chip power-down input (active low)
Analog ground
1.8V analog V
Analog ground
Factory test pin - float for normal operation
Factory test pin - float for normal operation
Analog ground
1.8V analog V
Fiber signal detect/factory test pin
DD
DD
M9999-020606
KSZ8993M/ML