HC55183ECM Intersil, HC55183ECM Datasheet - Page 8

• Manufacturer Part Number: HC55183ECM
• Manufacturer: Intersil

Specifications of HC55183ECM

• Number Of Channels: 1
• On-hook Transmission: Yes
• Polarity Reversal: Yes
• On-chip Ring Relay Driver: Yes
• Longitudinal Balanced: 45
• Operating Supply Voltage (typ): 5/-28V
• Operating Temp Range: 0C to 70C
• Package Type: PLCC
• Loop Current Limit: 45mA
• Operating Temperature Classification: Commercial
• Pin Count: 28
• Mounting: Surface Mount
• Operating Current: 8.5mA
• Operating Supply Voltage (max): 5.25/-75V
• Operating Supply Voltage (min): 4.75/-24V
• Lead Free Status / RoHS Status: Not Compliant

Electrical Specifications
NOTES:
10. The device represents a low output impedance during ringing. Therefore the voltage across the ringing load is determined by the voltage divider formed by the protection resistance, loop
11. The HC55180, HC55183 and HC55184 are specified with a single longitudinal balance grade.
12. Longitudinal Balance is tested per IEEE455-1985, with 368Ω per Tip and Ring Terminal.
13. These parameters are tested 100% at room temperature. These parameters are guaranteed not tested across temperature via statistical characterization.
14. The HC55180, HC55183 and HC55184 do not support uncommitted switch operation.
15. The HC55183 and HC55184 do not support the Forward Loopback operating mode.
16. The HC55183 and HC55184 do not support the Tip Open operating mode.
17. The power dissipation numbers are actual device measurements and will be less than worse case calculations based on data sheet supply current limits.
18. Characterized with 2 x 10µs, and 10 x 1000µs first level lightning surge waveforms (GR-1089-CORE).
Low Power Standby
(Note 2)
Ringing
(Note 2)
OFF HOOK POWER DISSIPATION (Notes 5, 17)
Forward or Reverse
7. The HC55180 does not provide battery switch operation. Therefore all battery voltage references will be made to V
8. Ringing Voltage is measured with VRS = 0.839 V
9. The HC55183 and HC55184 devices are specified with a single high battery voltage grade.
and V
resistance and ringing load impedance.
PARAMETER
BH
pins. See the HC55180 Basic Application Circuit.
V
V
V
V
V
TEST CONDITIONS
B
B
B
B
B
Unless Otherwise Specified, T
loop current limit = 25mA. All AC Parameters are specified at 600Ω 2-wire terminating impedance over the frequency band of 300Hz to 3.4kHz.
Protection resistors = 0Ω. (Continued)
= -85V
= -100V
= -85V
= -100V
= -24V
HC55180 (NOTE 7)
RMS
MIN
for -100V devices, VRS = 0.707 V
-
-
-
-
-
TYP
190
220
290
A
52
59
= 0°C to 70°C for the HC55183, 184 only, all others -40°C to 85°C, V
MAX
-
-
-
-
-
V
V
V
V
V
TEST CONDITIONS
BH
BH
BH
BH
BL
= -24V
= -85V
= -100V
= -85V
= -100V
RMS
for -85V devices and VRS = 0.619 V
HC55181
MIN
-
-
-
-
-
TYP
190
220
290
52
59
B
. V
B
MAX
is the voltage applied to the common connection of the device V
300
325
310
75
80
V
(Note 9)
V
(Note 9)
V
TEST CONDITIONS
BH
BH
BL
RMS
= -24V
= -75V
= -75V
BL
for -75V devices. All measurements are at T = 25°C.
= -24V, V
HC55183, HC55184
CC
= +5V, AGND = BGND = 0V,
MIN
-
-
-
-
-
TYP
170
280
46
-
-
MAX
275
310
70
-
-
UNITS
mW
mW
mW
mW
mW
BL