PIC24FJ32GA104-I/PT Microchip Technology, PIC24FJ32GA104-I/PT Datasheet - Page 57

• Manufacturer Part Number: PIC24FJ32GA104-I/PT
• Description: 16-bit, 16 MIPS, 32KB Flash, 8KB RAM, Nanowatt XLP 44 TQFP 10x10x1mm TRAY
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FJ32GA104-I/PT

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 32KB (11K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

5.6.2
If a Flash location has been erased, it can be pro-
grammed using table write instructions to write an
instruction word (24-bit) into the write latch. The
TBLPAG register is loaded with the 8 Most Significant
Bytes of the Flash address. The TBLWTL and TBLWTH
EXAMPLE 5-7:
EXAMPLE 5-8:
 2010 Microchip Technology Inc.
; Setup a pointer to data Program Memory
; Setup NVMCON for programming one word to data Program Memory
// C example using MPLAB C30
//Set up NVMCON for word programming
//Set up pointer to the first memory location to be written
//Perform TBLWT instructions to write latches
MOV
MOV
MOV
MOV
MOV
TBLWTL W2, [W0]
TBLWTH W3, [W0++]
MOV
MOV
DISI
MOV
MOV
MOV
MOV
BSET
NOP
NOP
unsigned int offset;
unsigned long progAddr = 0xXXXXXX;
unsigned int progDataL = 0xXXXX;
unsigned char progDataH = 0xXX;
NVMCON = 0x4003;
TBLPAG = progAddr>>16;
offset = progAddr & 0xFFFF;
__builtin_tblwtl(offset, progDataL);
__builtin_tblwth(offset, progDataH);
asm(“DISI #5”);
__builtin_write_NVM();
PROGRAMMING A SINGLE WORD
OF FLASH PROGRAM MEMORY
#tblpage(PROG_ADDR), W0
W0, TBLPAG
#tbloffset(PROG_ADDR), W0
#LOW_WORD, W2
#HIGH_BYTE, W3
#0x4003, W0
W0, NVMCON
#5
#0x55, W0
W0, NVMKEY
#0xAA, W0
W0, NVMKEY
NVMCON, #WR
PROGRAMMING A SINGLE WORD OF FLASH PROGRAM MEMORY
(ASSEMBLY LANGUAGE CODE)
PROGRAMMING A SINGLE WORD OF FLASH PROGRAM MEMORY
(C LANGUAGE CODE)
PIC24FJ64GA104 FAMILY
;
;Initialize PM Page Boundary SFR
;Initialize a register with program memory address
;
;
; Write PM low word into program latch
; Write PM high byte into program latch
;
; Set NVMOP bits to 0011
; Disable interrupts while the KEY sequence is written
; Write the key sequence
; Start the write cycle
; Insert two NOPs after the erase
; Command is asserted
// Address of word to program
// Data to program lower word
// Data to program upper byte
// Initialize NVMCON
// Initialize PM Page Boundary SFR
// Initialize lower word of address
// Write to address low word
// Write to upper byte
// Block interrupts with priority < 7
// for next 5 instructions
// C30 function to perform unlock
// sequence and set WR
instructions write the desired data into the write latches
and specify the lower 16 bits of the program memory
address to write to. To configure the NVMCON register
for a word write, set the NVMOP bits (NVMCON<3:0>)
to ‘0011’. The write is performed by executing the
unlock sequence and setting the WR bit (see
Example 5-7).
DS39951C-page 57