IS45S16100C1-7TA1 ISSI, Integrated Silicon Solution Inc, IS45S16100C1-7TA1 Datasheet - Page 7

• Manufacturer Part Number: IS45S16100C1-7TA1
• Manufacturer: ISSI, Integrated Silicon Solution Inc
• Type: SDRAMr

Specifications of IS45S16100C1-7TA1

• Organization: 1Mx16
• Density: 16Mb
• Address Bus: 12b
• Access Time (max): 6/5.5ns
• Maximum Clock Rate: 143MHz
• Operating Supply Voltage (typ): 3.3V
• Package Type: TSOP-II
• Operating Temp Range: -40C to 85C
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Supply Current: 150mA
• Pin Count: 50
• Mounting: Surface Mount
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Not Compliant

IS45S16100C1
AC CHARACTERISTICS
Symbol Parameter
Notes:
1. When power is first applied, memory operation should be started 100 µs after V
2. Measured with t
3. The reference level is 1.4 V when measuring input signal timing. Rise and fall times are measured between V
4. Access time is measured at 1.4V with the load shown in the figure below.
5. The time t
Integrated Silicon Solution, Inc. — www.issi.com —
Rev. C
01/03/06
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
CK
CK
AC
AC
CHI
CL
OH
OH
LZ
HZ
HZ
DS
DH
AS
AH
CKS
CKH
CKA
CS
CH
RC
RAS
RP
RCD
RRD
DPL
DPL
DAL
DAL
T
REF
power-on
sequence must be executed before starting memory operation.
output is in the high impedance state.
3
2
3
2
3
2
3
2
3
2
3
2
Clock Cycle Time
Access Time From CLK
CLK HIGH Level Width
CLK LOW Level Width
Output Data Hold Time
Output LOW Impedance Time
Output HIGH Impedance Time
Input Data Setup Time
Input Data Hold Time
Address Setup Time
Address Hold Time
CKE Setup Time
CKE Hold Time
CKE to CLK Recovery Delay Time
Command Setup Time (CS, RAS, CAS, WE, DQM)
Command Hold Time (CS, RAS, CAS, WE, DQM)
Command Period (REF to REF / ACT to ACT)
Command Period (ACT to PRE)
Command Period (PRE to ACT)
Active Command To Read / Write Command Delay Time
Command Period (ACT [0] to ACT[1])
Input Data To Precharge
Command Delay time
Input Data To Active / Refresh
Command Delay time (During Auto-Precharge)
Transition Time
Refresh Cycle Time (4096)
HZ
(max.) is defined as the time required for the output voltage to transition by ± 200 mV from V
T
= 1 ns.
(4)
(1,2,3)
(5)
CAS Latency = 3
CAS Latency = 2
CAS Latency = 3
CAS Latency = 2
CAS Latency = 3
CAS Latency = 2
CAS Latency = 3
CAS Latency = 2
CAS Latency = 3
CAS Latency = 2
CAS Latency = 3
CAS Latency = 2
1-800-379-4774
DD
and V
DDQ
reach their stipulated voltages. Also note that the
1CLK+t
1CLK+t
1CLK+3
1CLK
1CLK
Min.
2.5
2.5
2.0
2.5
63
42
20
16
14
—
—
—
—
—
7
8
0
2
1
2
1
2
1
2
1
1
RP
RP
OH
-7
100,000
(min.) or V
IH
Max.
5.5
5.5
10
64
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
(min.) and V
6
6
OL
(max.) when the
IL
ISSI
(max.).
Units
ms
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
®
7