NP8P128A13T1760E Micron Technology Inc, NP8P128A13T1760E Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
NP8P128A13T1760E
Manufacturer Part Number
NP8P128A13T1760E
Description
Manufacturer
Micron Technology Inc
Datasheet
1.NP8P128A13T1760E.pdf
(94 pages)
Specifications of NP8P128A13T1760E
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NP8P128A13T1760E
Manufacturer:
TI
Quantity:
1 043
Company:
Part Number:
NP8P128A13T1760E
Manufacturer:
Micron Technology Inc
Quantity:
10 000
4.0
Table 5:
Datasheet
16
A[MAX:1]
DQ[15:0]
CE# or S#
OE# or
HOLD#
RST#
WE#
WP#
C
D
Q
SERIAL
V
V
V
V
V
NC
DU
RFU
PP
CC
CCQ
SS
SSQ
Symbol
Output
Input/
Ball/Pin Descriptions
Type
Input
Input
Input
Input
Input
Input
SPI
SPI
SPI
SPI
SPI
SPI
Pwr
Pwr
Pwr
Pwr
Pwr
Signals
ADDRESS INPUTS: Device address inputs. 128-Mbit: A[23:1]
Note: The address bus for TSOP and Easy BGA starts at A1. Numonyx® Omneo™ P8P PCM uses x16
addressing. The Numonyx® Omneo™ P8P PCM package is x8 addressing and is compatible with J3 or P30
products.
DATA INPUT/OUTPUTS: Inputs data and commands during writes (internally latched). Outputs data
during read operations. Data signals float when CE# or OE# are V
CHIP ENABLE: CE#-low activates internal control logic, I/O buffers, decoders, and sense amps. CE#-
high deselects the device, places it in standby state, and places data outputs at high-Z.
SPI Select: S# low activates command writes to the SPI interface. Raising S# to VIH completes (or
terminates) the SPI command cycle; it also sets Q to high-Z.
OUTPUT ENABLE: Active low OE# enables the device’s output data buffers during a read cycle. With
OE# at V
SPI HOLD#: When asserted, suspends the current cycle and sets Q to high-Z until de-asserted.
RESET CHIP: When low, RST# resets internal automation and inhibits write operations. This provides
data protection during power transitions. RST#-high enables normal operation. The device is in 8-Word
page mode array read after reset exits.
WRITE ENABLE: controls Command User Interface (CUI) and array writes. Its rising edge latches
addresses and data.
WRITE PROTECT: Disables/enables the lock-down function.
When WP# is V
lock-down.
When WP# is V
now locked; software can unlock and lock them. After WP# goes low, blocks previously marked lock-
down revert to that state.
SPI Clock: Synchronization clock for input and output data
SPI Data Input: Serial data input for Op Codes, address and program data bytes. Input data is clocked
in on the rising edge of C, starting with the MSB.
SPI Data Output: Serial data output for read data. Output data is clocked out, triggered by the falling
edge of C, starting with the MSB.
SPI Enable: SERIAL is a port select switching between the normal parallel or serial interface. When Vss,
the normal (non-SPI) Numonyx® Omneo™ P8P PCM interface is enabled; all other SPI inputs are Don't
Care, and Q is at High-Z. When Vcc, SPI mode is enabled, all non-SPI inputs are Don't Care, and all
outputs are at High-Z.
This pin has an internal weak pull down resistor to select the normal parallel interface when users leave
the pin floating. A CAM can be used to permanently disable this feature.
ERASE AND WRITE POWER: A valid V
be altered when V
Set V
the system supply, V
Program/erase voltage is normally 1.7 V–3.6 V.
DEVICE POWER SUPPLY: Writes are inhibited at V
should not be attempted.
OUTPUT POWER SUPPLY: Enables all outputs to be driven at V
V
GROUND: connects device circuitry to system ground.
I/O GROUND: Tie to GND
NO CONNECT: No internal connection; can be driven or floated.
DON’T USE: Don’t connect to power supply or other signals.
RESERVED FOR FUTURE USE: Don’t connect to other signals.
CC
if V
PP
CCQ
= V
IH
, device data outputs are placed in high-Z state.
CC
is to function within the V
for in-system program and erase operations. To accommodate resistor or diode drops from
IL
IH
PP
, the lock-down mechanism is enabled and software cannot unlock blocks marked
, the lock-down mechanism is disabled and blocks previously locked-down are
≤ V
PP
’s V
PPLK.
IH
level can be as low as V
CC
PP
range.
Name and Function
voltage allows erase or programming. Memory contents can’t
CC
PPLMIN
≤ V
LKO
.
. Device operations at invalid V
CCQ
Numonyx® Omneo™ P8P Datasheet
IH
. or RST# is V
. This input may be tied directly to
IL
.
CC
August 2010
316144-07
voltages