CY8C5487LTI-007 Cypress Semiconductor Corp, CY8C5487LTI-007 Datasheet - Page 55

• Manufacturer Part Number: CY8C5487LTI-007
• Manufacturer: Cypress Semiconductor Corp

Specifications of CY8C5487LTI-007

• Lead Free Status / RoHS Status: Compliant

Figure 8-12. Sample and Hold Topology
(Φ1 and Φ2 are opposite phases of a clock)
8.11.1 Down Mixer
The S+H can be used as a mixer to down convert an input signal.
This circuit is a high bandwidth passive sample network that can
sample input signals up to 14 MHz. This sampled value is then
held using the opamp with a maximum clock rate of 4 MHz. The
output frequency is at the difference between the input frequency
and the highest integer multiple of the Local Oscillator that is less
than the input.
8.11.2 First Order Modulator - SC Mode
A first order modulator is constructed by placing the switched
capacitor block in an integrator mode and using a comparator to
provide a 1-bit feedback to the input. Depending on this bit, a
reference voltage is either subtracted or added to the input
signal. The block output is the output of the comparator and not
the integrator in the modulator case. The signal is downshifted
and buffered and then processed by a decimator to make a
delta-sigma converter or a counter to make an incremental
converter. The accuracy of the sampled data from the first-order
modulator is determined from several factors.
The main application for this modulator is for a low frequency
ADC with high accuracy. Applications include strain gauges,
thermocouples, precision voltage, and current measurement
9. Programming, Debug Interfaces,
The Cortex-M3 has internal debugging components, tightly
integrated with the CPU, providing the following features:
Document Number: 001-55036 Rev. *F
V
V
JTAG or SWD access
Flash Patch and Breakpoint (FPB) block for implementing
breakpoints and code patches
Data Watchpoint and Trigger (DWT) block for implementing
watchpoints, trigger resources, and system profiling
Embedded Trace Macrocell (ETM) for instruction trace
Instrumentation Trace Macrocell (ITM) for support of printf-style
debugging
n
i
ref
Resources
Φ
Φ
Φ
Φ
2
2
1
1
C
C
1
3
Φ
Φ
Φ
Φ
1
2
2
1
C
C
2
4
PRELIMINARY
Φ
Φ
Φ
Φ
1
2
1
2
V
V
ref
ref
V
out
PSoC devices include extensive support for programming,
testing, debugging, and tracing both hardware and firmware.
Four interfaces are available: JTAG, SWD, SWV, and
TRACEPORT. JTAG and SWD support all programming and
debug features of the device. JTAG also supports standard JTAG
scan chains for board level test and chaining multiple JTAG
devices for programming or testing. The SWV and TRACEPORT
provide trace output from the DWT, ETM, and ITM.
TRACEPORT is faster but uses more pins. SWV is slower but
uses only one pin.
Cortex-M3 debug and trace functionality enables full device
debugging in the final system using the standard production
device. It does not require special interfaces, debugging pods,
simulators, or emulators. Only the standard programming
connections are required to fully support debug.
The PSoC Creator IDE software provides fully integrated
programming and debug support for PSoC devices. The low cost
MiniProg3 programmer and debugger is designed to provide full
programming and debug support of PSoC devices in conjunction
with the PSoC Creator IDE. PSoC JTAG, SWD, and SWV inter-
faces are fully compatible with industry standard third party tools.
All Cortex-M3 debug and trace modules are disabled by default
and can only be enabled in firmware. If not enabled, the only way
to reenable them is to erase the entire device, clear flash
protection, and reprogram the device with new firmware that
enables them. Disabling debug and trace features, robust flash
protection, and hiding custom analog and digital functionality
inside the PSoC device provide a level of security not possible
with multichip application solutions. Additionally, all device inter-
faces can be permanently disabled (Device Security) for applica-
tions concerned about phishing attacks due to a maliciously
reprogrammed device. Permanently disabling interfaces is not
recommended in most applications because the designer then
cannot access the device. Because all programming, debug, and
test interfaces are disabled when Device Security is enabled,
PSoCs with Device Security enabled may not be returned for
failure analysis.
9.1 JTAG Interface
The IEEE 1149.1 compliant JTAG interface exists on four or five
pins (the nTRST pin is optional). The JTAG clock frequency can
be up to 8 MHz, or 1/3 of the CPU clock frequency for 8 and 16-bit
transfers, or 1/5 of the CPU clock frequency for 32-bit transfers,
whichever is least. By default, the JTAG pins are enabled on new
devices but the JTAG interface can be disabled, allowing these
pins to be used as General Purpose I/O (GPIO) instead. The
JTAG interface is used for programming the flash memory,
debugging, I/O scan chains, and JTAG device chaining.
9.2 SWD Interface
The SWD interface is the preferred alternative to the JTAG
interface. It requires only two pins instead of the four or five
needed by JTAG. SWD provides all of the programming and
debugging features of JTAG at the same speed. SWD does not
provide access to scan chains or device chaining. The SWD
clock frequency can be up to 1/3 of the CPU clock frequency.
SWD uses two pins, either two of the JTAG pins (TMS and TCK)
or the USBIO D+ and D- pins. The USBIO pins are useful for in
system programming of USB solutions that would otherwise
require a separate programming connector. One pin is used for
PSoC
®
5: CY8C54 Family Data
Page 55 of 97
[+] Feedback
[+] Feedback