M41T65Q6F STMicroelectronics, M41T65Q6F Datasheet - Page 27

• Manufacturer Part Number: M41T65Q6F
• Description: IC RTC SERIAL W/ALARM 16QFN
• Manufacturer: STMicroelectronics
• Type: Clock/Calendar/Alarmr

Specifications of M41T65Q6F

• Memory Size: 16B
• Time Format: HH:MM:SS:hh (24 hr)
• Date Format: YY-MM-DD-dd
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.3 V ~ 4.4 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-QFN
• Function: Clock/Calendar/Alarm/Timer Interrupt
• Rtc Memory Size: 16 Byte
• Supply Voltage (max): 4.4 V
• Supply Voltage (min): 1.3 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Rtc Bus Interface: Serial (2-Wire, I2C)
• Supply Current: 50 uA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-3908-2

M41T62/63/64/65
3.4
Note:
Note:
3.5
Note:
Watchdog timer
The watchdog timer can be used to detect an out-of-control microprocessor. The user
programs the watchdog timer by setting the desired amount of time-out into the watchdog
register, address 09h.
Bits BMB4-BMB0 store a binary multiplier and the three bits RB2-RB0 select the resolution
where:
000=1/16 second (16 Hz);
001=1/4 second (4 Hz);
010=1 second (1 Hz);
011=4 seconds (1/4 Hz); and
100 = 1 minute (1/60 Hz).
Invalid combinations (101, 110, and 111) will NOT enable a watchdog time-out. Setting
BMB4-BMB0 = 00000 with any combination of RB2-RB0, other than 000, will result in an
immediate watchdog time-out.
The amount of time-out is then determined to be the multiplication of the five-bit multiplier
value with the resolution. (For example: writing 00001110 in the watchdog register = 3*1 or 3
seconds). If the processor does not reset the timer within the specified period, the M41T6x
sets the WDF (watchdog flag) and generates an interrupt on the IRQ pin (M41T62), or a
watchdog output pulse (M41T63 and M41T65 only) on the WDO pin. The watchdog timer
can only be reset by having the microprocessor perform a WRITE of the watchdog register.
The time-out period then starts over.
Should the watchdog timer time-out, any value may be written to the watchdog register in
order to clear the IRQ pin. A value of 00h will disable the watchdog function until it is again
programmed to a new value. A READ of the flags register will reset the watchdog flag (bit
D7; register 0Fh). The watchdog function is automatically disabled upon power-up, and the
watchdog register is cleared.
A WRITE to any clock register will restart the watchdog timer.
Watchdog output (WDO - M41T63/65 only)
If the processor does not reset the watchdog timer within the specified period, the watchdog
output (WDO) will pulse low for t
connected to the reset input of the processor in order to generate a processor reset. After a
watchdog time-out occurs, the timer will remain disabled until such time as a new
countdown value is written into the watchdog register.
The crystal oscillator must be running for the WDO pulse to be available.
The WDO output is an N-channel, open drain output driver (with I
on page
33).
Doc ID 10397 Rev 15
rec
(see
Table 18 on page
35). This output may be
OL
as specified in
Clock operation
Table 14
27/43