AD7653AST Analog Devices Inc, AD7653AST Datasheet - Page 18

• Manufacturer Part Number: AD7653AST
• Description: IC ADC 16BIT 1MSPS W/REF 48-LQFP
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of AD7653AST

• Rohs Status: RoHS non-compliant
• Number Of Bits: 16
• Sampling Rate (per Second): 1M
• Data Interface: Serial, Parallel
• Number Of Converters: 1
• Power Dissipation (max): 145mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• For Use With: EVAL-AD7653CBZ - BOARD EVALUATION FOR AD7653

AD7653
Voltage Reference Input
The AD7653 allows the choice of either a very low temperature
drift internal voltage reference or an external 2.5 V reference.
Unlike many ADCs with internal references, the internal
reference of the AD7653 provides excellent performance and
can be used in almost all applications.
To use the internal reference along with the internal buffer,
PDREF and PDBUF should both be LOW. This will produce a
1.207 V voltage on REFBUFIN which, amplified by the buffer,
will result in a 2.5 V reference on the REF pin.
The output impedance of REFBUFIN is 11 k
the reference is enabled.
a 100 nF ceramic capacitor. Thus, the 100 nF capacitor provides
an RC filter for noise reduction.
To use an external reference along with the internal buffer,
PDREF should be HIGH and PDBUF should be LOW. This
powers down the internal reference and allows the 2.5 V
reference to be applied to REFBUFIN.
To use an external reference directly on the REF pin, PDREF
and PDBUF should both be HIGH.
PDREF and PDBUF, respectively, power down the internal
reference and the internal reference. Note that the PDREF and
PDBUF input current should never exceed 20 mA. This could
eventually occur when input voltage is above AVDD (for
instance at power-up). In this case, a 100 Ω series resistor is
recommended.
The internal reference is temperature compensated to 2.5 V ±
20 mV. The reference is trimmed to provide a typical drift of 7
ppm/°C
For improved drift performance, an external reference such as
the
The AD7653 voltage reference input REF has a dynamic input
impedance; it should, therefore, be driven by a low impedance
source with efficient decoupling between the REF and REFGND
inputs. This decoupling depends on the choice of the voltage
reference, but usually consists of a low ESR capacitor connected
to REF and REFGND with minimum parasitic inductance. A
10 µF (X5R, 1206 size) ceramic chip capacitor (or 47 µF
tantalum capacitor) is appropriate when using either the
internal reference or one of these recommended reference
voltages:
•
•
•
AD780
The low noise, low temperature drift
The low power
The low cost
. This typical drift characteristic is shown in
can be used.
AD1582
ADR291
It is useful to decouple REFBUFIN with
ADR421
Ω (minimum) when
and
Figure 17
AD780
Rev. A | Page 18 of 28
.
For applications that use multiple AD7653s, it is more effective
to use the internal buffer to buffer the reference voltage.
Care should be taken with the voltage reference’s temperature
coefficient, which directly affects the full-scale accuracy, if this
parameter matters. For instance, a ±15 ppm/°C temperature
coefficient of the reference changes full scale by ±1 LSB/°C.
Note that V
input range is defined in terms of V
increase the range to 0 V to 3 V with an AVDD above 4.85 V.
The
The TEMP pin, which measures the temperature of the AD7653,
can be used as shown in
is applied to one of the inputs of the analog switch (e.g.,
ADG779), and the ADC itself is used to measure its own
temperature. This configuration is very useful for improving the
calibration accuracy over the temperature range.
Power Supply
The AD7653 uses three power supply pins: an analog 5 V supply
AVDD, a digital 5 V core supply DVDD, and a digital
input/output interface supply OVDD. OVDD allows direct
interface with any logic between 2.7 V and DVDD + 0.3 V. To
reduce the supplies needed, the digital core (DVDD) can be
supplied through a simple RC filter from the analog supply, as
shown in
supply sequencing once OVDD does not exceed DVDD by
more than 0.3 V, and is thus free of supply voltage induced
latch-up.
ANALOG INPUT
(UNIPOLAR)
AD780
Figure 22
Figure 24. Temperature Sensor Connection Diagram
REF
can be selected with a 3 V reference voltage.
can be increased to AVDD – 1.85 V. Since the
ADG779
. The AD7653 is independent of power
AD8021
Figure 24
C
C
. The output of the TEMP pin
REF
IN
, this would essentially
TEMP
AD7653
TEMPERATURE
SENSOR
02966-0-024