MAX11359AETL+ Maxim Integrated Products, MAX11359AETL+ Datasheet - Page 44

• Manufacturer Part Number: MAX11359AETL+
• Description: IC DAS SYSTEM 16BIT 40-TQFN
• Manufacturer: Maxim Integrated Products
• Type: Data Acquisition System (DAS)r

Specifications of MAX11359AETL+

• Resolution (bits): 16 b
• Sampling Rate (per Second): 477
• Data Interface: MICROWIRE™, QSPI™, Serial, SPI™
• Voltage Supply Source: Analog and Digital
• Voltage - Supply: 1.8 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 40-TQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16-Bit Data-Acquisition System with ADC, DAC,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
The PWM_CTRL register contains control bits for the 8-
bit PWM.
PWME: PWM-enable bit. Set PWME = 1 to enable the
internal PWM, and set PWME = 0 to disable the internal
PWM. Enable the high-frequency clock before enabling
the PWM when using input clock frequencies above
32.768kHz. The power-on default state is 0.
FSEL<2:0>: Frequency selection bits. Selects the PWM
input clock frequency as shown in Table 14. The
power-on default is 000.
PWM_CTRL Register (Power-On State: 0000 0000 00XX XXXX)
Table 14. Setting the PWM Frequency
* The lower PWM frequencies are useful for power-supply duty
cycling to conserve battery life and enable a single-battery cell-
powered system. The higher frequencies allow reasonably small,
external components for RC filtering when used as a DAC for bias
adjustments.
** When the part is in sleep mode, the HFCK is shut down. In this
case, PWM frequencies above 32kHz are not available (see
SPWME in the SLEEP_CFG Register section).
44
PWM INPUT FREQUENCY*
PWME
______________________________________________________________________________________
SPD1
MSB
4915.2**
2457.6**
1228.8**
32.768
(kHz)
8.192
1.024
0.256
0.032
FSEL2
SPD2
FSEL2
0
0
0
0
1
1
1
1
FSEL1
X
FSEL1
0
0
1
1
0
0
1
1
FSEL0
FSEL0
X
0
1
0
1
0
1
0
1
SWAH: SWA-switch PWM-high control bit. Set SWAH =
1 to enable the PWM output to directly control the SWA
switch. When SWAH = SWAL, the PWM output is dis-
abled from controlling the SWA switch. When SWAH =
1, a PWM high output closes the SWA switch and a
PWM low output opens the SWA switch. The PWM high
output refers to the beginning of the period when the
output is logic-high. See Table 17 for more details. The
power-on default is 0.
SWAL: SWA-switch PWM-low control bit. Set SWAL = 1
to enable the inverted PWM output to directly control
the SWA switch. When SWAH = SWAL, the PWM output
is disabled from controlling the SWA switch. When
SWAL = 1, a PWM low output closes the SWA switch
and a PWM high output opens the SWA switch. The
PWM low output refers to the end of the period when
the output is logic-low. See Table 17 for more details.
The power-on default is 0.
SPD1: SPDT1-switch PWM drive control bit. Set SPD1
= 1 to enable the PWM output to directly control the
SPDT1 switch, and set SPD1 = 0 to disable the PWM
output controlling the SPDT1 switch. The SPDT1<1:0>
bits, the UPIO pins (if programmed), and the PWM out-
put (if enabled), determine the SPDT1-switch state. See
Table 18 for more details. The power-on default is 0.
SPD2: SPDT2-switch PWM drive control bit. Set SPD2
= 1 to enable the PWM output to directly control the
SPDT2 switch, and set SPD2 = 0 to disable the PWM
output controlling the SPDT2 switch. The SPDT2<1:0>
bits, the UPIO pins (if programmed), and the PWM out-
put (if enabled), determine the SPDT2-switch state. See
Table 19 for more details. The power-on default is 0.
SWAH
X
SWAL
X
X
X
LSB
X
X