X95820WV14IZ-2.7T1 Intersil, X95820WV14IZ-2.7T1 Datasheet - Page 9

• Manufacturer Part Number: X95820WV14IZ-2.7T1
• Description: IC POT DGTL DUAL 10K OHM 14TSSOP
• Manufacturer: Intersil
• Series: XDCP™r

Specifications of X95820WV14IZ-2.7T1

• Taps: 256
• Resistance (ohms): 10K
• Number Of Circuits: 2
• Temperature Coefficient: 45 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Resistance In Ohms: 10K
• Number Of Elements: 2
• # Of Taps: 256
• Resistance (max): 10KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (I2C)
• Single Supply Voltage (typ): 3.3V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 14
• Package Type: TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: X95820WV14IZ-2.7T1TR

Principles of Operation
The X95820 in as integrated circuit incorporating two DCPs
with their associated registers, non-volatile memory, and a
I
a host and the potentiometers and memory.
DCP Description
Each DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of each
DCP are equivalent to the fixed terminals of a mechanical
potentiometer (RH and RL pins). The RW pin of each DCP is
connected to intermediate nodes, and is equivalent to the
wiper terminal of a mechanical potentiometer. The position
of the wiper terminal within the DCP is controlled by an 8-bit
volatile Wiper Register (WR). Each DCP has its own WR.
When the WR of a DCP contains all zeroes (WR<7:0>: 00h),
its wiper terminal (RW) is closest to its “Low” terminal (RL).
When the WR of a DCP contains all ones (WR<7:0>: FFh),
its wiper terminal (RW) is closest to its “High” terminal (RH).
As the value of the WR increases from all zeroes (00h) to all
ones (255 decimal), the wiper moves monotonically from the
position closest to RL to the closest to RH. At the same time,
the resistance between RW and RL increases monotonically,
while the resistance between RH and RW decreases
monotonically.
While the X95820 is being powered up, all two WRs are
reset to 80h (128 decimal), which locates RW roughly at the
center between RL and RH. Soon after the power supply
voltage becomes large enough for reliable non-volatile
memory reading, the X95820 reads the value stored on two
different non-volatile Initial Value Registers (IVRs) and loads
them into their corresponding WRs.
The WRs and IVRs can be read or written directly using the
I
Memory Description
The X95820 contains eight non-volatile bytes. they are
accessed by I
through 7 decimal. The first two non-volatile bytes at
addresses 0 and 1 contain the initial value loaded at power-
up into the volatile Wiper Registers (WRs) of DCP0 and
DCP1 respectively. Bytes at addresses 2, 3, 4, 5, and 6 are
available to the user as general purpose registers. The byte
at address 7 is reserved; the user should not write to it, and
its value should be ignored if read.
The volatile WR, and the non-volatile Initial Value Register
(IVR) of a DCP are accessed with the same Address Byte.
A volatile byte at address 8 decimal, controls what byte is
read or written when accessing DCP registers: the WR, the
IVR, or both.
2
2
C serial interface providing direct communication between
C serial interface as described in the following sections.
2
C interface operations with Address Bytes 0
9
X95820
When the byte at address 8 is all zeroes, which is the default
at power up:
• A read operation to addresses 0 or 1 outputs the value of
• A write operation to addresses 0 or 1 writes the same
When the byte at address 8 is 80h (128 decimal):
• A read operation to addresses 0 or 1 outputs the value of
• A write operation to addresses 0 or 1only writes to the
It is not possible to write to an IVR without writing the same
value to its corresponding WR.
00h and 80h are the only values that should be written to
address 8. All other values are reserved and must not be
written to address 8.
To access the general purpose bytes at addresses 2, 3, 4, 5,
or 6, the value at address 8 must be all zeros.
The X95820 is pre-programmed with 80h in the two IVRs.
WR: Wiper Register, IVR: Initial value Register.
I
The X95820 supports a bidirectional I
protocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as the
receiver. The device controlling the transfer is a master and
the device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, the X95820
operates as a slave device in all applications.
All communication over the I
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (See
Figure 15). On power up of the X95820 the SDA pin is in the
input mode.
2
ADDRESS
the non-volatile IVRs.
value to the WR and IVR of the corresponding DCP.
the volatile WR.
corresponding volatile WR.
C Serial Interface
8
7
6
5
4
3
2
1
0
General Purpose
NON-VOLATILE
TABLE 1. MEMORY MAP
IVR1
IVR0
-
2
C interface is conducted by
Reserved
2
C bus oriented
Access Control
Not Available
VOLATILE
WR1
WR0
July 18, 2006
FN8212.2