AD5254BRUZ50 Analog Devices Inc, AD5254BRUZ50 Datasheet - Page 20
![IC POT DGTL QUAD 50K 20TSSOP](/photos/6/56/65613/ru-20_sml.jpg)
AD5254BRUZ50
Manufacturer Part Number
AD5254BRUZ50
Description
IC POT DGTL QUAD 50K 20TSSOP
Manufacturer
Analog Devices Inc
Datasheet
1.AD5254BRUZ100.pdf
(32 pages)
Specifications of AD5254BRUZ50
Memory Type
Non-Volatile
Temperature Coefficient
650 ppm/°C Typical
Taps
256
Resistance (ohms)
50K
Number Of Circuits
4
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V, ±2.25 V ~ 2.75 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-TSSOP
Resistance In Ohms
50K
End To End Resistance
50kohm
Track Taper
Linear
Resistance Tolerance
± 30%
No. Of Steps
256
No. Of Pots
Quad
Potentiometer Ic Case
RoHS Compliant
Supply Voltage Range
± 2.25V To ± 2.75V
Control Interface
I2C, Serial
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD5254EVAL - BOARD EVAL FOR AD5254
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD5254BRUZ50
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD5253/AD5254
I
The first byte of the AD5253/AD5254 is a slave address byte
(see Figure 33 and Figure 34). It has a 7-bit slave address and an
R/ W bit. The 5 MSB of the slave address is 01011, and the next
2 LSB is determined by the states of the AD1 and AD0 pins.
AD1 and AD0 allow the user to place up to four
AD5253/AD5254 devices on one bus.
AD5253/AD5254 can be controlled via an I
bus and are connected to this bus as slave devices. The 2-wire
I
1.
2.
2
2
C serial bus protocol (see Figure 33 and Figure 34) follows:
C-COMPATIBLE 2-WIRE SERIAL BUS
The master initiates a data transfer by establishing a start
condition, such that SDA goes from high to low while SCL
is high (see Figure 33). The following byte is the slave
address byte, which consists of the 5 MSB of a slave address
defined as 01011. The next two bits are AD1 and AD0, I
device address bits. Depending on the states of their AD1
and AD0 bits, four AD5253/AD5254 devices can be
addressed on the same bus. The last LSB, the R/ W bit,
determines whether data is read from or written to the
slave device.
The slave whose address corresponds to the transmitted
address responds by pulling the SDA line low during the
ninth clock pulse (this is called an acknowledge bit). At
this stage, all other devices on the bus remain idle while
the selected device waits for data to be written to or read
from its serial register.
In the write mode (except when restoring EEMEM to the
RDAC register), there is an instruction byte that follows
the slave address byte. The MSB of the instruction byte is
labeled CMD/ REG . MSB = 1 enables CMD, the command
instruction byte; MSB = 0 enables general register writing.
The third MSB in the instruction byte, labeled EE/ RDAC ,
is true when MSB = 0 or when the device is in general
writing mode. EE enables the EEMEM register, and REG
enables the RDAC register. The 5 LSB, A4 to A0, designates
START BY
MASTER
SCL
SDA
1
0
START BY
MASTER
1
SLAVE ADDRESS BYTE
SCL
SDA
0
FRAME 1
1
1 AD1 AD0 R/W
1
0
1
SLAVE ADDRESS BYTE
2
0
C-compatible serial
FRAME1
1
ACK. BY
AD525x
9
1
1
X
Figure 33. General I
Figure 34. General I
AD1 AD0
X
Rev. B | Page 20 of 32
2
X
INSTRUCTION BYTE
C
R/W
ACK. BY
AD525x
X
FRAME 2
9
X
2
D7
2
C Write Pattern
1
C Read Pattern
X
3.
4.
D6
X
D5
the addresses of the EEMEM and RDAC registers (see
Figure 27
device is in CMD mode, the four bits following the MSB
are C3 to C1, which correspond to 12 predefined EEMEM
controls and quick commands; there are also four factory-
reserved commands. The 3 LSB—A2, A1, and A0—are 4-
channel RDAC addresses (see
acknowledging the instruction byte, the last byte in the
write mode is the data byte. Data is transmitted over the
serial bus in sequences of nine clock pulses (eight data bits
followed by an acknowledge bit). The transitions on the
SDA line must occur during the low period of SCL and
remain stable during the high period of SCL (see
In current read mode, the RDAC0 data byte immediately
follows the acknowledgment of the slave address byte.
After an acknowledgement, RDAC1 follows, then RDAC2,
and so on. (There is a slight difference in write mode,
where the last eight data bits representing RDAC3 data are
followed by a no acknowledge bit.) Similarly, the
transitions on the SDA line must occur during the low
period of SCL and remain stable during the high period of
SCL (see Figure 34). Another reading method, random
read method, is shown in Figure 30.
When all data bits have been read or written, a stop
condition is established by the master. A stop condition is
defined as a low-to-high transition on the SDA line that
occurs while SCL is high. In write mode, the master pulls
the SDA line high during the 10
stop condition (see Figure 33). In read mode, the master
issues a no acknowledge for the ninth clock pulse, that is,
the SDA line remains high. The master brings the SDA line
low before the 10
line high to establish a stop condition (see Figure 34).
X
RDAC REGISTER
ACK. BY
AD525x
D4
9
FRAME 2
D3
D7 D6 D5
1
and
D2
Figure 28
D1
th
DATA BYTE
D4 D3 D2 D1
D0
FRAME 1
clock pulse and then brings the SDA
NO ACK. BY
MASTER
9
). When MSB = 1 or when the
STOP BY
MASTER
Figure 31
th
D0
clock pulse to establish a
ACK. BY
AD525x
9
). After
STOP BY
MASTER
Figure 33
).