5962-8960101B2A QP SEMICONDUCTOR, 5962-8960101B2A Datasheet - Page 5

• Manufacturer Part Number: 5962-8960101B2A
• Manufacturer: QP SEMICONDUCTOR

Specifications of 5962-8960101B2A

• Logic Family: ACT
• Technology: CMOS
• Number Of Bits: 8
• Number Of Elements: 1
• Clock-edge Trigger Type: Positive-Edge
• Polarity: Non-Inverting
• Operating Supply Voltage (typ): 5V
• Propagation Delay Time: 13.5ns
• Output Type: 3-State
• Low Level Output Current: 24mA
• High Level Output Current: -24mA
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temp Range: -55C to 125C
• Operating Temperature Classification: Military
• Mounting: Surface Mount
• Pin Count: 20
• Lead Free Status / Rohs Status: Not Compliant

DSCC FORM 2234
APR 97
MIL-PRF-38535 and herein for device classes B, S, Q, and V or MIL-PRF-38535, appendix A and herein for device class M.
on figure 5.
revision level control and shall be made available to the preparing or acquiring activity upon request.
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
tests for each subgroup are defined in table I.
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes B, S, Q, and V shall be in accordance with MIL-PRF-38535. Marking for device class M
shall be in accordance with MIL-PRF-38535, appendix A.
required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535,
appendix A.
QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a
certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in
MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of
supply for this drawing shall affirm that the manufacturer's product meets, for device classes B, S, Q, and V, the requirements of
MIL-PRF-38535 and herein or for device class M the requirements of MIL-PRF-38535, appendix A and herein.
or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
herein) involving devices acquired to this drawing is required for any change that effects this drawing.
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
microcircuit group number 38 (see MIL-PRF-38535, appendix A).
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table. The truth table shall be as specified on figure 3.
3.2.5 Ground bounce load circuit and waveforms. The ground bounce load circuit and waveforms shall be as specified
3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 6.
3.2.7 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
3.5.1 Certification/compliance mark. The certification mark for device classes B, S, Q, and V shall be a "QML" or "Q" as
3.6 Certificate of compliance. For device classes B, S, Q, and V, a certificate of compliance shall be required from a
3.7 Certificate of conformance. A certificate of conformance as required for device classes B, S, Q, and V in MIL-PRF-38535
3.8 Notification of change for device class M. For device class M notification to DSCC-VA of change of product (see 6.2
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 4.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
3.11 Substitution. Substitution data shall be as indicated in the appendix herein.
DEFENSE SUPPLY CENTER COLUMBUS
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43216-5000
STANDARD
SIZE
A
REVISION LEVEL
E
SHEET
5962-89601
5