20-101-1094 Rabbit Semiconductor, 20-101-1094 Datasheet - Page 18
![MCU RCM4000 RABBITCORE](/photos/6/74/67480/20-101-1094_sml.jpg)
20-101-1094
Manufacturer Part Number
20-101-1094
Description
MCU RCM4000 RABBITCORE
Manufacturer
Rabbit Semiconductor
Datasheet
1.20-101-1094.pdf
(130 pages)
Specifications of 20-101-1094
Module/board Type
MPU Core Module
Product
Microcontroller Modules
Core Processor
Rabbit 4000
Clock Speed
58.98 MHz
Interface Type
Ethernet, Serial
Flash
512 KB
Timers
10 x 8 bit, 1 x 10 bit, 1 x 16 bit
Operating Supply Voltage
3 V to 3.6 V
Board Size
47 mm x 61 mm x 20 mm
Core
RCM4000
Processor Series
RCM4000
Cpu Core
Rabbit 4000
For Use With/related Products
RCM4000
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1139
2.3 Run a Sample Program
Once the RCM4000/RCM4010/RCM4050 is connected as described in the preceding pages,
start Dynamic C by double-clicking on the Dynamic C icon on your desktop or in your
Start
If you are using a USB port to connect your computer to the RCM4000/RCM4010/
RCM4050, click on the “Communications” tab and verify that
verter
determine which COM port was assigned to the RS-232/USB converter. Open
Panel > System > Hardware > Device Manager > Ports
used for the USB connection. In Dynamic C, select
select this COM port on the
port number followed by
side the range on the dropdown menu.
Now find the file
gram, open it with the
selecting
play a small square bouncing around in a box.
2.3.1 Troubleshooting
If Dynamic C appears to compile the BIOS successfully, but you then receive a communi-
cation error message when you compile and load a sample program, it is possible that your
PC cannot handle the higher program-loading baud rate. Try changing the maximum
download rate to a slower baud rate as follows.
• Locate the
If a program compiles and loads, but then loses target communication before you can
begin debugging, it is possible that your PC cannot handle the default debugging baud
rate. Try lowering the debugging baud rate as follows.
• Locate the
If you receive the message No Rabbit Processor Detected, the programming
cable may be connected to the wrong COM port, a connection may be faulty, or the target
system may not be powered up. First, check to see that the power LED on the Prototyping
Board is lit and that the jumper across pins 5–6 of header JP10 on the Prototyping Board is
installed. If the LED is lit, check both ends of the programming cable to ensure that it is
firmly plugged into the PC and the programming header on the RCM4000 with the marked
(colored) edge of the programming cable towards pin 1 of the programming header. Ensure
that the module is firmly and correctly installed in its connector on the Prototyping Board.
If there are no faults with the hardware, select a different COM port within Dynamic C as
explained for the USB port above. Press
BIOS. If Dynamic C still reports it is unable to locate the target system, repeat the above
steps for another available COM port. You should receive a Bios compiled success-
fully message once this step is completed successfully.
12
Communications
Communications
menu.
is selected to support the USB programming cable. Click
Run
Serial Options
Serial Options
in the
PONG.C
Run
menu. Select a slower Max download baud rate. Click
menu. Choose a lower debug baud rate. Click
File
Enter
menu. The
, which is in the Dynamic C
menu, compile it using the
Communications
dialog in the Dynamic C
dialog in the Dynamic C
on your computer keyboard if the COM port number is out-
STDIO
<Ctrl-Y>
window will open on your PC and will dis-
tab, then click
to force Dynamic C to recompile the
Options > Project Options
Compile
SAMPLES
Options > Project Options >
Options > Project Options >
and identify which COM port is
OK
Use USB to Serial Con-
menu, and then run it by
OK
folder. To run the pro-
. You may type the COM
. You may have to
OK
RabbitCore RCM4000
to save.
OK
Control
, then
to save.