CY7C66113-PVC Cypress Semiconductor Corp, CY7C66113-PVC Datasheet - Page 39

• Manufacturer Part Number: CY7C66113-PVC
• Description: IC MCU 8K USB HUB 4 PORT 56TSSOP
• Manufacturer: Cypress Semiconductor Corp

Specifications of CY7C66113-PVC

• Applications: USB Hub/Microcontroller
• Core Processor: M8
• Program Memory Type: OTP (8 kB)
• Controller Series: USB Hub
• Ram Size: 256 x 8
• Interface: I²C, USB, HAPI
• Number Of I /o: 31
• Voltage - Supply: 4 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-SSOP
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 56
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: CY3649 - PROGRAMMER HI-LO USB M8428-1339 - KIT LOW SPEED PERSONALITY BOARD
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant
• Other names: 428-1330

Table 18-2. Control Bit Definition for Upstream Port
Bit 3 : Bus Activity
Bits 4 and 5 : D– Upstream and D+ Upstream
Bit 6 : Endpoint Mode
Bit 7 : Endpoint Size
The hub generates an EOP at EOF1 in accordance with the USB 1.1 Specification, Section 11.2.2.
19.0
The CY7C66x13 SIE supports operation as a single device or a compound device. This section describes the two device
addresses, the configurable endpoints, and the endpoint function.
19.1
The USB Controller provides two USB Device Address Registers: A (addressed at 0x10)and B (addressed at 0x40). Upon reset
and under default conditions, Device A has three endpoints and Device B has two endpoints. The USB Device Address Register
contents are cleared during a reset, setting the USB device addresses to zero and disabling these addresses. Figure 19-1 shows
the format of the USB Address Registers.
USB Device Address (Device A, B)
Bits[6..0] :Device Address
Bit 7: Device Address Enable
19.2
The CY7C66x13 controller supports up to two addresses and five endpoints for communication with the host. The configuration
of these endpoints, and associated FIFOs, is controlled by bits [7,6] of the USB Status and Control Register (see Figure 18-11).
Bit 7 controls the size of the endpoints and bit 6 controls the number of addresses. These configuration options are detailed in
Table 19-1. Endpoint FIFOs are part of user RAM (as shown in Section 5.4.1).
Document #: 38-08024 Rev. *A
Bit #
Bit Name
Read/Write
Reset
This is a “sticky” bit that indicates if any non-idle USB event has occurred on the upstream USB port. Firmware should
check and clear this bit periodically to detect any loss of bus activity. Writing a ‘0’ to the Bus Activity bit clears it, while writing
a ‘1’ preserves the current value. In other words, the firmware can clear the Bus Activity bit, but only the SIE can set it.
These bits give the state of each upstream port pin individually: 1 = HIGH, 0 = LOW.
This bit used to configure the number of USB endpoints. See Section 19.2 for a detailed description.
This bit used to configure the number of USB endpoints. See Section 19.2 for a detailed description.
Firmware writes this bits during the USB enumeration process to the non-zero address assigned by the USB host.
Must be set by firmware before the SIE can respond to USB traffic to the Device Address.
USB Device Addresses
USB Device Endpoints
USB SIE Operation
Control Bits
000
001
010
100
101
011
110
111
7
Device
Address
Enable
R/W
0
6
Device
Address
Bit 6
R/W
0
Not Forcing (SIE Controls Driver)
Force D+[0] HIGH, D–[0] LOW
Force D+[0] LOW, D–[0] HIGH
Force SE0; D+[0] LOW, D–[0] LOW
Force D+[0] LOW, D–[0] LOW
Force D+[0] HiZ, D–[0] LOW
Force D+[0] LOW, D–[0] HiZ
Force D+[0] HiZ, D–[0] HiZ
5
Device
Address
Bit 5
R/W
0
Figure 19-1. USB Device Address Registers
4
Device
Address
Bit 4
R/W
0
3
Device
Address
Bit 3
R/W
0
Control Action
2
Device
Address
Bit 2
R/W
0
ADDRESSES
1
Device
Address
Bit 1
R/W
0
CY7C66013
CY7C66113
0x10(A) and 0x40(B)
Page 39 of 58
0
Device
Address
Bit 0
R/W
0