MPC850DSLZQ50BU Freescale Semiconductor, MPC850DSLZQ50BU Datasheet - Page 19

• Manufacturer Part Number: MPC850DSLZQ50BU
• Description: IC MPU PWRQUICC 50MHZ 256-PBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC850DSLZQ50BU

• Processor Type: MPC8xx PowerQUICC 32-Bit
• Speed: 50MHz
• Voltage: 3.3V
• Mounting Type: Surface Mount
• Package / Case: 256-PBGA
• Family Name: MPC8xx
• Device Core: PowerQUICC
• Device Core Size: 32b
• Frequency (max): 50MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Supply Voltage (max): 3.465V
• Operating Supply Voltage (min): 3.135V
• Operating Temp Range: 0C to 95C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 256
• Package Type: BGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Lead Free Status / Rohs Status: Not Compliant

1
For a frequency F, the following equations should be applied to each one of the above parameters:
For minima:
For maxima:
where:
D is the parameter value to the frequency required in ns
F is the operation frequency in MHz
D
CAP LOAD is the capacitance load on the signal in question.
FFACTOR is the one defined for each of the parameters in the table.
2
3
4
5
6
7
8
9
10
11
Figure 6-2 is the control timing diagram.
MOTOROLA
50
The minima provided assume a 0 pF load, whereas maxima assume a 50pF load. For frequencies not marked on the
part, new bus timing must be calculated for all frequency-dependent AC parameters. Frequency-dependent AC
parameters are those with an entry in the FFactor column. AC parameters without an FFactor entry do not need to
be calculated and can be taken directly from the frequency column corresponding to the frequency marked on the
part. The following equations should be used in these calculations.
Phase and frequency jitter performance results are valid only if the input jitter is less than the prescribed value.
If the rate of change of the frequency of EXTAL is slow (i.e. it does not jump between the minimum and maximum
values in one cycle) or the frequency of the jitter is fast (i.e., it does not stay at an extreme value for a long time) then
the maximum allowed jitter on EXTAL can be up to 2%.
The timing for BR output is relevant when the MPC850 is selected to work with external bus arbiter. The timing for BG
output is relevant when the MPC850 is selected to work with internal bus arbiter.
The setup times required for TA, TEA, and BI are relevant only when they are supplied by an external device (and not
when the memory controller or the PCMCIA interface drives them).
The timing required for BR input is relevant when the MPC850 is selected to work with the internal bus arbiter. The
timing for BG input is relevant when the MPC850 is selected to work with the external bus arbiter.
The D[0–31] and DP[0–3] input timings B20 and B21 refer to the rising edge of the CLKOUT in which the TA input
signal is asserted.
The D[0:31] and DP[0:3] input timings B20 and B21 refer to the falling edge of CLKOUT. This timing is valid only for
read accesses controlled by chip-selects controlled by the UPM in the memory controller, for data beats where DLT3
= 1 in the UPM RAM words. (This is only the case where data is latched on the falling edge of CLKOUT.
The timing B30 refers to CS when ACS = '00' and to WE[0:3] when CSNT = '0'.
The signal UPWAIT is considered asynchronous to CLKOUT and synchronized internally. The timings specified in
B37 and B38 are specified to enable the freeze of the UPM output signals.
The AS signal is considered asynchronous to CLKOUT.
is the parameter value defined for 50 MHz
Freescale Semiconductor, Inc.
MPC850 (Rev. A/B/C) Hardware Specifications
For More Information On This Product,
Go to: www.freescale.com
Layout Practices
19