CS42448-CQZ Cirrus Logic Inc, CS42448-CQZ Datasheet - Page 61
![IC CODEC 108DB 192KHZ 64LQFP](/photos/6/80/68063/mfg_cs42448_series_sml.jpg)
CS42448-CQZ
Manufacturer Part Number
CS42448-CQZ
Description
IC CODEC 108DB 192KHZ 64LQFP
Manufacturer
Cirrus Logic Inc
Type
Audio Codecr
Datasheet
1.CS42448-CQZ.pdf
(64 pages)
Specifications of CS42448-CQZ
Package / Case
64-LQFP
Data Interface
Serial
Resolution (bits)
24 b
Number Of Adcs / Dacs
6 / 8
Sigma Delta
Yes
Dynamic Range, Adcs / Dacs (db) Typ
105 / 108 (Differential), 102 / 105 (Single-Ended)
Voltage - Supply, Analog
3.14 V ~ 5.25 V
Voltage - Supply, Digital
3.14 V ~ 5.25 V
Operating Temperature
-10°C ~ 70°C
Mounting Type
Surface Mount
Number Of Adc Inputs
10
Number Of Dac Outputs
8
Conversion Rate
192 KSPS
Interface Type
Serial (I2C, SPI)
Resolution
24 bit
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 10 C
Number Of Channels
6 ADC/8 DAC
Thd Plus Noise
- 98 dB ADC / - 98 dB DAC, - 95 dB ADC / - 95 dB DAC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
598-1151 - BOARD EVAL FOR CS42448 CODEC
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
598-1033
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS42448-CQZ
Manufacturer:
Vishay
Quantity:
4 529
Company:
Part Number:
CS42448-CQZ
Manufacturer:
CRYSTAL
Quantity:
455
Company:
Part Number:
CS42448-CQZ
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Part Number:
CS42448-CQZ
Manufacturer:
CIRRUS
Quantity:
20 000
Company:
Part Number:
CS42448-CQZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
DS648F3
10.PARAMETER DEFINITIONS
Dynamic Range
Total Harmonic Distortion + Noise
Frequency Response
Interchannel Isolation
Interchannel Gain Mismatch
Gain Error
Gain Drift
Offset Error
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
bandwidth. Dynamic Range is a signal-to-noise ratio measurement over the specified band width made with
a -60 dBFS signal. 60 dB is added to resulting measurement to refer the measurement to full-scale. This
technique ensures that the distortion components are below the noise level and do not affect the measure-
ment. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991,
and the Electronic Industries Association of Japan, EIAJ CP-307. Expressed in decibels.
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
band width (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Measured
at -1 and -20 dBFS as suggested in AES17-1991 Annex A.
A measure of the amplitude response variation from 10 Hz to 20 kHz relative to the amplitude response at
1 kHz. Units in decibels.
A measure of crosstalk between the left and right channel pairs. Measured for each channel at the convert-
er's output with no signal to the input under test and a full-scale signal applied to the other channel. Units in
decibels.
The gain difference between left and right channel pairs. Units in decibels.
The deviation from the nominal full-scale analog output for a full-scale digital input.
The change in gain value with temperature. Units in ppm/°C.
The deviation of the mid-scale transition (111...111 to 000...000) from the ideal. Units in mV.
CS42448
61