CS42528-CQZ Cirrus Logic Inc, CS42528-CQZ Datasheet - Page 38

• Manufacturer Part Number: CS42528-CQZ
• Description: IC CODEC S/PDIF RCVR 64LQFP
• Manufacturer: Cirrus Logic Inc
• Type: General Purposer

Specifications of CS42528-CQZ

• Package / Case: 64-LQFP
• Data Interface: Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 8
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 114 / 114
• Voltage - Supply, Analog: 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.13 V ~ 5.25 V
• Operating Temperature: -10°C ~ 70°C
• Mounting Type: Surface Mount
• Number Of Adc Inputs: 2
• Number Of Dac Outputs: 8
• Conversion Rate: 192 KSPS
• Interface Type: Serial (SPI)
• Resolution: 24 bit
• Operating Supply Voltage: 3.3 V, 5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 10 C
• Number Of Channels: 2 ADC/8 DAC
• Thd Plus Noise: - 100 dB ADC / - 100 dB DAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1503 - BOARD EVAL FOR CS42528/CS49300
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1038

38
4.7
4.7.1
CS
C C L K
C D IN
C D O U T
Control Port Description and Timing
The control port is used to access the registers, allowing the CS42528 to be configured for the desired op-
erational modes and formats. The operation of the control port may be completely asynchronous with re-
spect to the audio sample rates. However, to avoid potential interference problems, the control port pins
should remain static if no operation is required.
The control port has two modes: SPI and I²C, with the CS42528 acting as a slave device. SPI mode is se-
lected if there is a high-to-low transition on the AD0/CS pin after the RST pin has been brought high. I²C
mode is selected by connecting the AD0/CS pin through a resistor to VLC or DGND, thereby permanently
selecting the desired AD0 bit address state.
SPI Mode
In SPI mode, CS is the CS42528 chip-select signal; CCLK is the control port bit clock (input into the
CS42528 from the microcontroller); CDIN is the input data line from the microcontroller, and CDOUT is
the output data line to the microcontroller. Data is clocked in on the rising edge of CCLK and out on the
falling edge.
Figure 21
first seven bits on CDIN form the chip address and must be 1001111. The eighth bit is a read/write indi-
cator (R/W), which should be low to write. The next eight bits form the Memory Address Pointer (MAP),
which is set to the address of the register that is to be updated. The next eight bits are the data which will
be placed into the register designated by the MAP. During writes, the CDOUT output stays in the Hi-Z
state. It may be externally pulled high or low with a 47 kΩ resistor, if desired.
There is a MAP auto-increment capability, enabled by the INCR bit in the MAP register. If INCR is a zero,
the MAP will stay constant for successive read or writes. If INCR is set to a 1, the MAP will auto-increment
after each byte is read or written, allowing block reads or writes of successive registers.
To read a register, the MAP has to be set to the correct address by executing a partial write cycle which
finishes (CS high) immediately after the MAP byte. The MAP auto increment bit (INCR) may be set or not,
as desired. To begin a read, bring CS low, send out the chip address and set the read/write bit (R/W) high.
The next falling edge of CCLK will clock out the MSB of the addressed register (CDOUT will leave the high
impedance state). If the MAP auto-increment bit is set to 1, the data for successive registers will appear
consecutively.
ADDRESS
MAP = Memory Address Pointer, 8 bits, MSB first
1001111
C H IP
shows the operation of the control port in SPI mode. To write to a register, bring CS low. The
High Impedance
R/W
M A P
Figure 21. Control Port Timing in SPI Mode
MSB
b y te 1
DATA
b y te n
LSB
A D D R E S S
C H IP
1001111
R/W
MSB
LSB MSB
CS42528
LSB
DS586F1