PKM4113DPINB Ericsson Power Modules, PKM4113DPINB Datasheet - Page 22

• Manufacturer Part Number: PKM4113DPINB
• Description: DC/DC Converters & Regulators 12 Vdc 11A Iso Input 36-75V 132W
• Manufacturer: Ericsson Power Modules
• Series: PKM-Dr

Specifications of PKM4113DPINB

• Product: Isolated
• Output Power: 30 W
• Input Voltage Range: 36 V to 75 V
• Number Of Outputs: 1
• Output Voltage (channel 1): 1.5 V
• Output Current (channel 1): 20 A
• Isolation Voltage: 1.5 KV
• Package / Case Size: Quarter Brick
• Output Type: Isolated
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

E
Operating information
Input Voltage
The input voltage range 36 to 75Vdc meets the requirements
of the European Telecom Standard ETS 300 132-2 for normal
input voltage range in –48 and –60 Vdc systems, -40.5 to -
57.0 V and –50.0 to -72 V respectively.
At input voltages exceeding 75 V, the power loss will be higher
than at normal input voltage and T
absolute max +110°C. The absolute maximum continuous
input voltage is 80 Vdc.
Turn-off Input Voltage
The products monitor the input voltage and will turn on and
turn off at predetermined levels.
The minimum hysteresis between turn on and turn off input
voltage is 1V.
Remote Control (RC)
The maximum required sink current is 1 mA. When the RC pin
is left open, the voltage generated on the RC pin is
5.0 – 7.0 V. The standard product is provided with “negative
logic” remote control and will be off until the RC pin is
connected to the -In. To turn on the product the voltage
between RC pin and -In should be less than 1V. To turn off the
converter the RC pin should be left open, or connected to a
voltage higher than 13 V referenced to -In. In situations where
it is desired to have the product to power up automatically
without the need for control signals or a switch, the RC pin can
be wired directly to -In.
The second option is “positive logic” remote control, which can
be ordered by adding the suffix “P” to the end of the part
number. When the RC pin is left open, the product starts up
automatically when the input voltage is applied. Turn off is
achieved by connecting the RC pin to the -In. To ensure safe
turn off the voltage difference between RC pin and the -In pin
shall be less than 1V. The product will restart automatically
when this connection is opened.
See Design Note 021 for detailed information.
Input and Output Impedance
The impedance of both the input source and the load will
interact with the impedance of the product. It is important that
the input source has low characteristic impedance. The
products are designed for stable operation without external
capacitors connected to the input or output. The performance
Prepared (also subject responsible if other)
EXUEFYA
Approved
SEC/D (Betty Wu)
PKM 4000D PINB series
DC/DC converters, Input 36-75 V, Output up to 35 A/132 W
The products are fitted with a
remote control function referenced
to the primary negative input
connection (-In), with negative and
positive logic options available.
The RC function allows the product
to be turned on/off by an external
device like a semiconductor or
mechanical switch.
P1
must be limited to
Checked
EQUENXU
Ericsson Internal
PRODUCT SPECIFICATION
No.
3/1301-BMR 637 02 Uen
Date
2009-11-20
in some applications can be enhanced by addition of external
capacitance as described under External Decoupling
Capacitors.
If the input voltage source contains significant inductance, the
addition of a 22 - 100 µF capacitor across the input of the
product will ensure stable operation. The capacitor is not
required when powering the product from an input source with
an inductance below 10 µH. The minimum required
capacitance value depends on the output power and the input
voltage. The higher output power the higher input capacitance
is needed. Approximately doubled capacitance value is
required for a 24 V input voltage source compared to a 48V
input voltage source.
External Decoupling Capacitors
When powering loads with significant dynamic current
requirements, the voltage regulation at the point of load can
be improved by addition of decoupling capacitors at the load.
The most effective technique is to locate low ESR ceramic and
electrolytic capacitors as close to the load as possible, using
several parallel capacitors to lower the effective ESR. The
ceramic capacitors will handle high-frequency dynamic load
changes while the electrolytic capacitors are used to handle
low frequency dynamic load changes. It is equally important to
use low resistance and low inductance PCB layouts and
cabling.
External decoupling capacitors will become part of the
product’s control loop. The control loop is optimized for a wide
range of external capacitance and the maximum
recommended value that could be used without any additional
analysis is found in the Electrical specification.
The ESR of the capacitors is a very important parameter.
Stable operation is guaranteed with a verified ESR value of >5
mΩ across the output connections.
For further information please contact your local Ericsson
Power Modules representative.
Output Voltage Adjust (V
The products have an Output Voltage Adjust pin (V
pin can be used to adjust the output voltage above or below
Output voltage initial setting.
When increasing the output voltage, the voltage at the output
pins (including any remote sense compensation ) must be
kept below the threshold of the over voltage protection, (OVP)
to prevent the product from shutting down. At increased output
voltages the maximum power rating of the product remains the
same, and the max output current must be decreased
correspondingly.
To increase the voltage the resistor should be connected
between the V
Output voltage adjust function is according to information
given under the Output section for the respective product.
To decrease the output voltage, the resistor should be
connected between the V
adj
pin and +Sense pin. The resistor value of the
Technical Specification
EN/LZT 146 416 R3A February 2010
© Ericsson AB
Rev
E
adj
adj
pin and –Sense pin.
)
Reference
adj
). This
2 (6)
22