USB3300-EZK SMSC, USB3300-EZK Datasheet - Page 36
![IC USB HOST/OTG PHY ULPI 32-QFN](/photos/6/81/68178/32-qfn_pkg_sml.jpg)
USB3300-EZK
Manufacturer Part Number
USB3300-EZK
Description
IC USB HOST/OTG PHY ULPI 32-QFN
Manufacturer
SMSC
Type
Hi Speed USB Host Devicer
Datasheet
1.USB3300-EZK.pdf
(55 pages)
Specifications of USB3300-EZK
Controller Type
USB 2.0 Controller
Interface
USB
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
32-QFN
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Supply
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
638-1034
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
USB3300-EZK
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
USB3300-EZK-TR
Manufacturer:
MICRON
Quantity:
3 140
Part Number:
USB3300-EZK-TR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Revision 1.08 (11-07-07)
6.1.9.2
6.1.9.3
DATA[7:0]
Exiting Low Power Mode
To exit Low Power Mode, the Link will assert STP. Upon the assertion of STP, the USB3300 will begin
its start-up procedure. After the PHY start-up is complete, the PHY will start the clock on CLKOUT and
de-assert DIR. Once DIR has been de-asserted, the Link can de-assert STP when ready and start
operating in Synchronous Mode. The PHY will automatically set the SuspendM bit to a 1 in the
Function Control register.
The time from T0 to T1 is given in
page
Should the Link de-assert STP before DIR is de-asserted, the USB3300 will detect this as a false
resume request and return to Low Power Mode. This is detailed in section 3.9.4 of the ULPI 1.1
specification.
Interface Protection
ULPI protocol assumes that both the Link and PHY will keep the ULPI data bus driven by either the
Link when DIR is low or the PHY when DIR is high. The only exception is when DIR has changed
state and a turn around cycle occurs for 1 clock period.
In the design of a USB system, there can be cases where the Link may not be driving the ULPI bus
to a known state while DIR is low. Two examples where this can happen is because of a slow Link
start-up or a hardware reset.
START UP PROTECTION
Upon start-up, when the PHY de-asserts DIR, the Link must be ready to receive commands and drive
Idle on the data bus. If the Link is not ready to receive commands or drive Idle, it must assert STP
before DIR is de-asserted. The Link can then de-assert STP when it has completed its start-up. If the
Link doesn’t assert STP before it can receive commands, the PHY may interpret the databus state as
a TX CMD and transmit invalid data onto the USB bus, or make invalid register writes.
A Link should be designed to have the default POR state of the STP output high and the data bus tri-
stated. The USB3300 has weak pull-downs on the DATA bus to prevent these inputs from floating
when not driven.
NXT
CLK
STP
DIR
15.
T0
POWER MODE
Note: Not to Scale
LOW
Figure 6.9 Exiting Low Power Mode
...
DATASHEET
T1
AROUND
Table 5.2, “Electrical Characteristics: CLKOUT Start-Up,” on
TURN
Hi-Speed USB Host, Device or OTG PHY with ULPI Low Pin Interface
36
T2
Fast Link Drives Bus
Idle and STP low
DATA BUS IGNORED (SLOW LINK)
T3
IDLE (FAST LINK)
T4
Slow Link Drives Bus
Idle and STP low
T5
IDLE
SMSC USB3300
Datasheet