DP83815CVNG National Semiconductor, DP83815CVNG Datasheet - Page 68

• Manufacturer Part Number: DP83815CVNG
• Description: IC CONTROLLER MEDIA ACCESS
• Manufacturer: National Semiconductor

Specifications of DP83815CVNG

• Controller Type: Ethernet Controller, MAC/BIU
• Interface: PCI
• Voltage - Supply: 3.3V
• Current - Supply: 170mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 144-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *DP83815CVNG

4.0 Register Set
4.3.2 Basic Mode Status Register
10:7
Bit
Bit
6:0
15
14
13
12
11
7
6
5
4
3
2
1
0
Jabber Detect Jabber Detect: Default: 0/LH
Collision Test Collision Test: Default: 0
100BASE-TX
100BASE-TX
Remote Fault Remote Fault: Default: 0/L(H)
100BASE-T4 100BASE-T4 Capable: Default: 0
Suppression
Half Duplex
Half Duplex
Full Duplex
Full Duplex
Negotiation
Negotiation
Link Status
Bit Name
Bit Name
10BASE-T
10BASE-T
Capability
Reserved
Reserved
Preamble
Complete
Extended
Ability
Auto-
Auto-
Offset: 0084h
(Continued)
Tag: BMSR
1 = Collision test enabled
0 = Normal operation
When set, this bit will cause the COL signal to be asserted in response to the assertion of TXEN within
512-bit times. The COL signal will be de-asserted within 4-bit times in response to the de-assertion of
TXEN.
Reserved: Default: 0, RO
0 = Device not able to perform 100BASE-T4 mode.
100BASE-TX Full Duplex Capable: Default: 1
1 = Device able to perform 100BASE-TX in full duplex mode
100BASE-TX Half Duplex Capable: Default: 1
1 = Device able to perform 100BASE-TX in half duplex mode.
10BASE-T Full Duplex Capable: Default: 1
1 = Device able to perform 10BASE-T in full duplex mode
10BASE-T Half Duplex Capable: Default: 1
1 = Device able to perform 10BASE-T in half duplex mode
Reserved: Write as 0, read as 0
Preamble suppression Capable: Default: 1
1 = Device able to perform management transaction with preamble suppressed, 32-bits of preamble
needed only once after reset, invalid opcode or invalid turnaround.
0 = Normal management operation
Auto-Negotiation Complete: Default: 0
1 = Auto-Negotiation process complete
0 = Auto-Negotiation process not complete
1 = Remote Fault condition detected (cleared on read or by reset). Fault criteria: Far End Fault Indication
or notification from Link Partner of Remote Fault.
0 = No remote fault condition detected
Auto Configuration Ability: Default: 1
1 = Device is able to perform Auto-Negotiation
0 = Device is not able to perform Auto-Negotiation
Link Status: Default: 0/L(L)
1 = Valid link established (for either 10 or 100 Mb/s operation)
0 = Link not established
The criteria for link validity is implementation specific. The occurrence of a link failure condition will cause
the Link Status bit to clear. Once cleared, this bit may only be set by establishing a good link condition
and a read via the management interface.
1 = Jabber condition detected
0 = No Jabber
This bit is implemented with a latching function, such that the occurrence of a jabber condition causes it
to set until it is cleared by a read to this register by the management interface or by a reset.
This bit only has meaning in 10 Mb/s mode.
Extended Capability: Default: 1
1 = Extended register capabilities
0 = Basic register set capabilities only
Access: Read Only
Size: 16 bits
68
Description
Description
Hard Reset: 7849h
www.national.com