S-1172B18-E6T1G Seiko Instruments, S-1172B18-E6T1G Datasheet - Page 15
![Low Dropout (LDO) Regulators Linear LDO reg Hi 70uA Iq 1000mA Iout](/photos/33/27/332784/hsop-6_sml.jpg)
S-1172B18-E6T1G
Manufacturer Part Number
S-1172B18-E6T1G
Description
Low Dropout (LDO) Regulators Linear LDO reg Hi 70uA Iq 1000mA Iout
Manufacturer
Seiko Instruments
Datasheet
1.S-1172B18-E6T1G.pdf
(35 pages)
Specifications of S-1172B18-E6T1G
Polarity
Positive
Input Voltage Max
6 V
Output Voltage
1.8 V
Output Type
Fixed
Dropout Voltage (max)
3 V at 300 mA
Output Current
1000 mA
Load Regulation
15 mV
Voltage Regulation Accuracy
1 %
Maximum Power Dissipation
1900 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
HSOP-6
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S-1172B18-E6T1G
Manufacturer:
SEIKO/精工
Quantity:
20 000
Rev.2.0
3. Shutdown pin (ON/OFF pin)
4. Overcurrent protection circuit
This pin starts and stops the regulator.
When the ON/OFF pin is set to the shutdown level, the entire internal circuit stops operating, and the built-in
P-channel MOS FET output transistor between the VIN and VOUT pin is turned off, in order to reduce the current
consumption significantly. The VOUT pin is set to the V
kΩ between the VOUT and VSS pin.
Note that the current consumption increases when a voltage of 0.3 V to 1.0 V is applied to the ON/OFF pin.
The ON/OFF pin is configured as shown in Figure 14. Since the ON/OFF pin is neither pulled down nor pulled up
internally, do not use it in the floating state.
When not using the ON/OFF pin, connect it to the VSS pin in the product A type, and connect it to the VIN pin in B
type.
The S-1172 Series has an overcurrent protection circuit having the characteristics shown in (1) Output Voltage vs.
Output Current (When load current is increased) (Ta = 25°C) in “
protect the output transistor against an excessive output current and short circuiting between the VOUT and VSS
pin. The current (I
initial value is restored for the output voltage, if releasing a short circuit once.
Caution This overcurrent protection circuit does not work as for thermal protection. If this IC long keeps
_00
Logic Type
ON/OFF
A
A
B
B
short circuiting inside, pay attention to the conditions of input voltage and load current so that,
under the usage conditions including short circuit, the loss of the IC will not exceed power
dissipation of the package.
Figure 14
“H”: Power off
“H”: Power on
“L”: Power on
“L”: Power off
HIGH RIPPLE-REJECTION LOW DROPOUT HIGH OUTPUT CURRENT CMOS VOLTAGE REGULATOR
SHORT
ON/OFF Pin
) when the output pin is short-circuited is internally set at approx. 200 mA (Typ.), and the
VSS
VIN
Internal Circuits
Operate
Operate
Stop
Stop
Seiko Instruments Inc.
Table 8
VOUT Pin Voltage
SS
Set value
Set value
V
V
SS
SS
level by the internal dividing resistor of several hundred
level
level
Characteristics (Typical Data)”, in order to
Current Consumption
I
I
I
I
SS1
SS2
SS2
SS1
S-1172 Series
15