S-1172B18-E6T1G Seiko Instruments, S-1172B18-E6T1G Datasheet - Page 17
![Low Dropout (LDO) Regulators Linear LDO reg Hi 70uA Iq 1000mA Iout](/photos/33/27/332784/hsop-6_sml.jpg)
S-1172B18-E6T1G
Manufacturer Part Number
S-1172B18-E6T1G
Description
Low Dropout (LDO) Regulators Linear LDO reg Hi 70uA Iq 1000mA Iout
Manufacturer
Seiko Instruments
Datasheet
1.S-1172B18-E6T1G.pdf
(35 pages)
Specifications of S-1172B18-E6T1G
Polarity
Positive
Input Voltage Max
6 V
Output Voltage
1.8 V
Output Type
Fixed
Dropout Voltage (max)
3 V at 300 mA
Output Current
1000 mA
Load Regulation
15 mV
Voltage Regulation Accuracy
1 %
Maximum Power Dissipation
1900 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
HSOP-6
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S-1172B18-E6T1G
Manufacturer:
SEIKO/精工
Quantity:
20 000
Rev.2.0
Precautions
• Wiring patterns for the VIN, VOUT and GND pins should be designed so that the impedance is low. When mounting
• Note that the output voltage may increase when a series regulator is used at low load current (1.0 mA or less).
• Note that the output voltage may generally increase due to the leakage current from a driver when a series regulator
• Generally series regulator may oscillate, depending on the selection of external parts. The following conditions are
• The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitance is
• Ringing may occur when these three conditions below are satisfied. Before selecting an input capacitor, be sure to
• If the output capacitance is small, power supply’s fluctuation and the characteristics of load fluctuation become worse.
• A momentary overshoot may be output when the power supply suddenly increases, and the output capacitance is
• The application conditions for the input voltage, output voltage, and load current should not exceed power dissipation
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
• In determining the output current, attention should be paid to the output current value specified in Table 7 in “
• SII claims no responsibility for any disputes arising out of or in connection with any infringement by products including
Sufficiently evaluate the output voltage’s fluctuation with the actual device.
an output capacitor between the VOUT and VSS pin (C
and VSS pin (C
is used at high temperature.
small, or an input capacitor is not connected. Note that the voltage regulator may oscillate when the value of the
input capacitor is greater than that of the output capacitor.
evaluate sufficiently under the actual usage conditions, including the temperature characteristics.
small. It is therefore important to sufficiently evaluate the output voltage at power application in actual device.
of the package.
protection circuit.
Electrical Characteristics” and footnote *5 of the table.
this IC of patents owned by a third party.
recommended for this IC. However, be sure to perform sufficient evaluation under the actual usage conditions for
selection, including the temperature characteristics. Regarding the equivalent series resistance (R
capacitor, refer to (5) Example of Equivalent Series Resistance vs. Output Current Characteristics (Ta = 25°C)
in “
Input capacitor (C
Output capacitor (C
The power supply inductance is high.
The load current is 100 mA or more.
The difference between the input voltage and the output voltage is close to the value of dropout voltage.
Reference Data”.
_00
IN
), the distance from the capacitors to these pins should be as short as possible.
HIGH RIPPLE-REJECTION LOW DROPOUT HIGH OUTPUT CURRENT CMOS VOLTAGE REGULATOR
IN
) :
L
) :
4.7 μF or more
4.7 μF or more
Seiko Instruments Inc.
L
) and a capacitor for stabilizing the input between the VIN
S-1172 Series
ESR
) for the output
17