BU2092F-E2 Rohm Semiconductor, BU2092F-E2 Datasheet - Page 22

IC DRIVER 12BIT S-IN P-OUT SOP18

BU2092F-E2

Manufacturer Part Number
BU2092F-E2
Description
IC DRIVER 12BIT S-IN P-OUT SOP18
Manufacturer
Rohm Semiconductor
Type
Driverr
Datasheets

Specifications of BU2092F-E2

Number Of Drivers/receivers
12/0
Voltage - Supply
2.7 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
18-SOP
Output Current
25mA
No. Of Outputs
12
Supply Voltage Range
2.7V To 5.5V
Driver Case Style
SOP
No. Of Pins
18
Operating Temperature Range
-20°C To +75°C
Svhc
No SVHC (18-Jun-2010)
Base
RoHS Compliant
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Supply Current
0.025 A
Maximum Operating Temperature
+ 75 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 25 C
Output Voltage
2 V to 1 V
Base Number
2092
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Protocol
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
BU2092F-E2TR

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
BU2092F-E2
Quantity:
2 000
Part Number:
BU2092F-E2
Manufacturer:
ROHM
Quantity:
1 000
Part Number:
BU2092F-E2
Manufacturer:
ROHM/罗姆
Quantity:
20 000
●Notes for use
© 2009 ROHM Co., Ltd. All rights reserved.
BU2050F,BU2092F,BU2092FV,BU2099FV,BD7851FP,BU2152FS
www.rohm.com
1. Absolute maximum ratings
2. Connecting the power supply connector backward
3. Power supply lines
4. GND voltage
5. Thermal design
6. Inter-pin shorts and mounting errors
7. Actions in strong electromagnetic field
8. Testing on application boards
9. Ground Wiring Pattern
10. Unused input terminals
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can
break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any
over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as
fuses.
Design PCB layout pattern to provide low impedance GND and supply lines. To obtain a low noise ground and supply line,
separate the ground section and supply lines of the digital and analog blocks. Furthermore, for all power supply terminals to
ICs, connect a capacitor between the power supply and the GND terminal. When applying electrolytic capacitors in the circuit,
not that capacitance characteristic values are reduced at low temperatures.
The potential of GND pin must be minimum potential in all operating conditions.
Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any
connection error or if pins are shorted together.
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction.
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or
removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic measure.
Use similar precaution when transporting or storing the IC.
Connect all unused input terminals to VDD or VSS in order to prevent excessive current or oscillation.
Insertion of a resistor (100kΩ approx.) is also recommended.
Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing
a single ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused
by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern
of any external components, either.
lines. An external direction diode can be added.
22/24
Technical Note
2009.06 - Rev.A

Related parts for BU2092F-E2