119384-02 AMETEK, 119384-02 Datasheet
![no-image](/images/no-image-200.jpg)
119384-02
Manufacturer Part Number
119384-02
Description
Low Voltage Brushless DC Blower 24 Volt
Manufacturer
AMETEK
Datasheet
1.119384-02.pdf
(2 pages)
12
5.0” (127mm) BLDC Low-Voltage Blower
12/24 VDC, Standard Flow System
* These part numbers are available through AMETEK Technical & Industrial Products’ distributors.
NOTES:
• Temperature: Working Air: 0°C to 45°C, Ambient Air: 0°C to 45°C, Storage Air: -40°C to 85°C.
• Dielectric Testing: 500 volts AC RMS 60Hz applied for one second between input pins and ground, one milliamps leakage max.
• Speed Control: Internal – E (Electrical): Pulse Width Modulated or Analog input voltage (user supplied), 0 to 5 Volts DC nominal.
• Models 119380 thru 119385 are dimensioned per the high output version - see following pages.
• Customized performance available upon request. Please contact AMETEK Technical & Industrial Products’ Marketing and Sales Department.
• Models 150016 and 150017 include a two (2) plane balancing option for reduced vibration per above drawing.
• Models 119380 thru 119385 can be confi gured and modifi ed for a two (2) plane balance option.
• When blowers are used in a vacuum condition, there will be an approximate reduction of 3% in the air performance.
• Standard hard mounting is done via the three (3) mounting bosses on the motor side of the blower.
• See controller section for models that require external drive electronics.
• Optional – cover shell with air inlet tube.
Voltage Input
Stages
Pressure, Maximum (Sealed Pressure)
Flow Rate, Maximum (Open Flow)
Drive Electronics
INCH
(MM)
Blower Data
3X Ø .38 BOSSES
EQUALLY SPACED ON A
Ø 3.228 BOLT CIRCLE.
(81.99)
6°±2°
(9.65)
External – These blowers require a 3 phase electronic commutated input to operate. A separate blower controller provides this input and
3X M5 X 0.8 THREAD HOLES
(6.35)
ON A Ø 3.228 BOLT CIRCLE.
.25
MODELS 119380 THRU 119385 ARE DIMENSIONED PER THE HIGH OUTPUT VERSION
MIN. DP. EQUALLY SPACED
70°±2°
(81.99)
58°±2°
M (Mechanical): A potentiometer is available for speed control of the blower. The potentiometer can be preset for a specifi c speed.
speed control. Refer to the controller section (page 118) of this catalog for additional information.
Ø
(127.0±0.76)
Unit of Measure
5.00±.03
Internal or External
(6.60±0.76)
(43.18±0.76)
.26±.03
1.70±.03
in. H
mBar
m
CFM
(6X)
VDC
—
(63.5±0.76)
3
/hr
2.50±.03
2
MFG. NAME,
MODEL NO., AND
DATE OF MFG.
O
(66.29±0.76)
2.61±.03
(6X)
Ø
(22.40±0.76)
(150017)*
(EXHAUST)
46°±2°
119380
External
.88±.03
13.5
33.6
32.3
54.9
12
1
18°±2°
(52.3±0.76)
2.06±.03
119381 M*
119382 E*
(6.10±1.52)
Ø
Internal
(63.50)
.24±.06
2.50
13.5
33.6
32.3
54.9
12
1
Part Number
3X
(8.89)
0.35
(39.87±1.52)
with AIR INLET TUBE
1.57±.06
COVER SHELL
OPTIONAL
(73.66±2.03)
2.90±.08
(44.70±1.02)
(150016)*
1.76±.04
119383
External
12.5
31.1
35.3
60.0
24
1
Ø
(38.10±0.76)
1.50±.03
(INTAKE)
CONNECTOR DETAIL
119384 M*
119385 E*
(32.26±0.76)
(31.75±0.76)
Internal
1.27±.03
1.25±.03
12.5
31.1
35.3
60.0
24
1
Ø B
Ø A
GROUND
S1
S2
S3
+5 VDC
Ø C
Related parts for 119384-02
119384-02 Summary of contents
Page 1
... OPTIONAL 1.25±.03 COVER SHELL (31.75±0.76) with AIR INLET TUBE Part Number 119381 M* 119383 119384 M* 119382 E* (150016)* 119385 13.5 12.5 12.5 33.6 31.1 31.1 32.3 35.3 35 ...
Page 2
... AMETEK BLDC motor controllers. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notifi ...