PIC16F676-I/ST Microchip Technology Inc., PIC16F676-I/ST Datasheet - Page 32

• Manufacturer Part Number: PIC16F676-I/ST
• Description: 14 PIN, 1.75 KB FLASH, 64 RAM, 12 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F676-I/ST

• Comparators: 1
• Cpu Speed: 5 MIPS
• Eeprom Memory: 128 Bytes
• Input Output: 12
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 14-pin TSSO
• Programmable Memory: 1.75K Bytes
• Ram Size: 64 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC16F630/676
4.3
When no prescaler is used, the external clock input is
the same as the prescaler output. The synchronization
of T0CKI, with the internal phase clocks, is accom-
plished by sampling the prescaler output on the Q2 and
Q4 cycles of the internal phase clocks. Therefore, it is
necessary for T0CKI to be high for at least 2T
REGISTER 4-1:
DS40039C-page 30
Using Timer0 with an External
Clock
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
OPTION_REG — OPTION REGISTER (ADDRESS: 81h)
bit 7
RAPU: PORTA Pull-up Enable bit
1 = PORTA pull-ups are disabled
0 = PORTA pull-ups are enabled by individual port latch values
INTEDG: Interrupt Edge Select bit
1 = Interrupt on rising edge of RA2/INT pin
0 = Interrupt on falling edge of RA2/INT pin
T0CS: TMR0 Clock Source Select bit
1 = Transition on RA2/T0CKI pin
0 = Internal instruction cycle clock (CLKOUT)
T0SE: TMR0 Source Edge Select bit
1 = Increment on high-to-low transition on RA2/T0CKI pin
0 = Increment on low-to-high transition on RA2/T0CKI pin
PSA: Prescaler Assignment bit
1 = Prescaler is assigned to the WDT
0 = Prescaler is assigned to the Timer0 module
PS2:PS0: Prescaler Rate Select bits
Legend:
R = Readable bit
- n = Value at POR
R/W-1
RAPU
Bit Value TMR0 Rate WDT Rate
000
001
010
011
100
101
110
111
INTEDG
R/W-1
OSC
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
R/W-1
T0CS
(and
W = Writable bit
’1’ = Bit is set
1 : 1
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
R/W-1
T0SE
a small RC delay of 20 ns) and low for at least 2T
(and a small RC delay of 20 ns). Refer to the electrical
specification of the desired device.
Note:
R/W-1
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
PSA
The ANSEL (9Fh) and CMCON (19h)
registers must be initialized to configure an
analog channel as a digital input. Pins
configured as analog inputs will read ‘0’.
The ANSEL register is defined for the
PIC16F676.
R/W-1
PS2
 2003 Microchip Technology Inc.
x = Bit is unknown
R/W-1
PS1
R/W-1
PS0
bit 0
OSC