W9751G6IB-3 Winbond Electronics, W9751G6IB-3 Datasheet - Page 7

• Manufacturer Part Number: W9751G6IB-3
• Manufacturer: Winbond Electronics
• Type: DDR2 SDRAMr

Specifications of W9751G6IB-3

• Organization: 32Mx16
• Density: 512Mb
• Address Bus: 15b
• Access Time (max): 450ps
• Maximum Clock Rate: 667MHz
• Operating Supply Voltage (typ): 1.8V
• Package Type: WBGA
• Operating Temp Range: 0C to 85C
• Operating Supply Voltage (max): 1.9V
• Operating Supply Voltage (min): 1.7V
• Supply Current: 160mA
• Pin Count: 84
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / Rohs Status: Compliant

5. BALL DESCRIPTION
M8,M3,M7,N2,N8,N3
,N7,P2,P8,P3,M2,P7
,R2
,F1,F9,C8,C2,D7,D3,
A9,C1,C3,C7,C9,E9,
G1,G3,G7,G9
A7,B2,B8,D2,D8,E7,
F2,F8,H2,H8
G8,G2,H7,H3,H1,H9
A2,E2,L1,R3,R7,R8
BALL NUMBER
A1,E1,J9,M9,R1
A3,E3,J3,N1,P9
D1,D9,B1,B9
K7,L7,K3
B7,A8
F7,E8
B3,F3
L2,L3
J8,K8
K9
K2
L8
J2
J7
J1
RAS , CAS ,
DQ0−DQ15
SYMBOL
BA0−BA1
A0−A12
UDQS,
LDQS,
UDQS
V
LDQS
V
V
V
V
UDM
ODT
LDM
CLK,
CLK
CKE
V
V
WE
SSDL
CS
NC
DDQ
SSQ
REF
DDL
DD
SS
On Die Termination
Reference Voltage
DLL Power Supply
LOW Data Strobe
DQ Power Supply
Command Inputs
Differential Clock
Input Data Mask
UP Data Strobe
No Connection
Power Supply
FUNCTION
Clock Enable
DLL Ground
Bank Select
Chip Select
DQ Ground
Data Input
Address
/ Output
Ground
Control
Inputs
Provide the row address for active commands, and the column
address and Auto-precharge bit for Read/Write commands to select
one location out of the memory array in the respective bank.
Row address: A0−A12.
Column address: A0−A9. (A10 is used for Auto-precharge)
BA0−BA1 define to which bank an ACTIVE, READ, WRITE or
PRECHARGE command is being applied.
Bi-directional data bus.
ODT (registered HIGH) enables termination resistance internal to the
DDR2 SDRAM.
Data Strobe for Lower Byte: Output with read data, input with write
data for source synchronous operation. Edge-aligned with read data,
center-aligned with write data. LDQS corresponds to the data on
DQ0−DQ7. LDQS is only used when differential data strobe mode
is enabled via the control bit at EMR (1)[A10 EMRS command].
Data Strobe for Upper Byte: Output with read data, input with write
data for source synchronous operation. Edge-aligned with read data,
center-aligned with write data. UDQS corresponds to the data on
DQ8−DQ15. UDQS is only used when differential data strobe mode
is enabled via the control bit at EMR (1)[A10 EMRS command].
All
HIGH
multiple ranks. CS is considered part of the command code.
entered.
DM is an input mask signal for write data. Input data is masked when
DM is sampled high coincident with that input data during a Write
access. DM is sampled on both edges of DQS. Although DM pins are
input only, the DM loading matches the DQ and DQS loading.
CLK and CLK are differential clock inputs. All address and control
input signals are sampled on the crossing of the positive edge of CLK
and negative edge of CLK . Output (read) data is referenced to the
crossings of CLK and CLK (both directions of crossing).
CKE (registered HIGH) activates and CKE (registered LOW)
deactivates clocking circuitry on the DDR2 SDRAM.
V
Power Supply: 1.8V ± 0.1V.
Ground.
DQ Power Supply: 1.8V ± 0.1V.
No connection.
DLL Ground.
DLL Power Supply: 1.8V ± 0.1V.
DQ Ground. Isolated on the device for improved noise immunity.
RAS , CAS and WE (along with CS ) define the command being
- 7 -
REF
.
commands
is reference voltage for inputs.
CS provides for external bank selection on systems with
are
Publication Release Date: Oct. 23, 2009
DESCRIPTION
masked
when
W9751G6IB
CS
Revision A06
is
registered