MAX7316ATE+T Maxim Integrated Products, MAX7316ATE+T Datasheet - Page 8
![IC I/O EXPANDER I2C 16B 16TQFN](/photos/6/66/66625/16-tqfn_exp_pad_21-0136_sml.jpg)
MAX7316ATE+T
Manufacturer Part Number
MAX7316ATE+T
Description
IC I/O EXPANDER I2C 16B 16TQFN
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX7316AEE.pdf
(24 pages)
Specifications of MAX7316ATE+T
Interface
I²C, SMBus
Number Of I /o
10
Interrupt Output
Yes
Frequency - Clock
400kHz
Voltage - Supply
2 V ~ 3.6 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
16-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The MAX7316 operates as a slave that sends and
receives data through an I
face. The interface uses a serial data line (SDA) and a
serial clock line (SCL) to achieve bidirectional commu-
nication between master(s) and slave(s). A master (typ-
ically a microcontroller) initiates all data transfers to and
from the MAX7316 and generates the SCL clock that
synchronizes the data transfer (Figure 2).
10-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
Figure 3. Start and Stop Conditions
Figure 4. Bit Transfer
Figure 5. Acknowledge
Figure 6. Slave Address
8
TRANSMITTER
SDA
SCL
SDA
SCL
RECEIVER
_______________________________________________________________________________________
CONDITION
SDA
SCL
SDA BY
SDA BY
START
SCL
S
CONDITION
START
DATA LINE STABLE;
S
MSB
DATA VALID
A6
1
CHANGE OF DATA
ALLOWED
1
2
2
C-compatible 2-wire inter-
Serial Interface
Serial Addressing
FOR ACKNOWLEDGE
0
CLOCK PULSE
8
CONDITION
0
STOP
9
P
A2
The MAX7316 SDA line operates as both an input and
an open-drain output. A pullup resistor, typically 4.7kΩ,
is required on SDA. The MAX7316 SCL line operates
only as an input. A pullup resistor, typically 4.7kΩ, is
required on SCL if there are multiple masters on the 2-
wire interface, or if the master in a single-master system
has an open-drain SCL output.
Each transmission consists of a START condition
(Figure 3) sent by a master, followed by the MAX7316
7-bit slave address plus R/W bit, a register address
byte, one or more data bytes, and finally a STOP condi-
tion (Figure 3).
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmis-
sion with a START (S) condition by transitioning SDA
from high to low while SCL is high. When the master
has finished communicating with the slave, it issues a
STOP (P) condition by transitioning SDA from low to
high while SCL is high. The bus is then free for another
transmission (Figure 3).
One data bit is transferred during each clock pulse.
The data on SDA must remain stable while SCL is high
(Figure 4).
The acknowledge bit is a clocked 9th bit that the recipi-
ent uses to handshake receipt of each byte of data
(Figure 5). Thus, each byte transferred effectively
requires 9 bits. The master generates the 9th clock
pulse, and the recipient pulls down SDA during the
acknowledge clock pulse so the SDA line is stable low
during the high period of the clock pulse. When the
master is transmitting to the MAX7316, the device gen-
erates the acknowledge bit because the MAX7316 is
the recipient. When the MAX7316 is transmitting to the
master, the master generates the acknowledge bit
because the master is the recipient.
The MAX7316 has a 7-bit long slave address (Figure 6).
The eighth bit following the 7-bit slave address is the
R/W bit. The R/W bit is low for a write command, high
for a read command.
0
LSB
0
Start and Stop Conditions
R/W
Slave Address
Acknowledge
Bit Transfer
ACK