LA-ISPPAC-POWR1014-01TN48E Lattice, LA-ISPPAC-POWR1014-01TN48E Datasheet - Page 18

• Manufacturer Part Number: LA-ISPPAC-POWR1014-01TN48E
• Description: IC, PROG POWER SUPPLY SUPERVISOR TQFP-48
• Manufacturer: Lattice
• Series: ispPAC®r

Specifications of LA-ISPPAC-POWR1014-01TN48E

• Input Voltage: 4.5V
• Supply Voltage Range: 2.8V To 3.96
• No. Of Pins: 48
• Operating Temperature Range: -40°C To +105°C
• No. Of Macrocells: 24
• Termination Type: SMD
• Supply Voltage Min: 2.8V
• Rohs Compliant: Yes
• Applications: General Purpose
• Voltage - Input: -0.3 V ~ 5.9 V
• Voltage - Supply: 2.8 V ~ 3.96 V
• Current - Supply: 20mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: *
• Package / Case: *
• Filter Terminals: SMD
• Frequency: 25MHz
• Input Voltage Primary Max: 4.5V
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Lattice Semiconductor
VMON Voltage Measurement with the On-chip Analog to Digital Converter
(ADC, LA-ispPAC-POWR1014A Only)
The LA-ispPAC-POWR1014A has an on-chip analog to digital converter that can be used for measuring the volt-
ages at the VMON inputs.
Figure 8. ADC Monitoring VMON1 to VMON10
Figure 8 shows the ADC circuit arrangement within the LA-ispPAC-POWR1014A device. The ADC can measure all
analog input voltages through the multiplexer, ADC MUX. The programmable attenuator between the ADC mux and
the ADC can be configured as divided-by-3 or divided-by-1 (no attenuation). The divided-by-3 setting is used to
measure voltages from 0V to 6V range and divided-by-1 setting is used to measure the voltages from 0V to 2V
range.
A microcontroller can place a request for any VMON voltage measurement at any time through the I
PAC-POWR1014A only). Upon the receipt of an I
VMON through the ADC MUX. The ADC output is then latched into the I
Calculation
The algorithm to convert the ADC code to the corresponding voltage takes into consideration the attenuation bit
value. In other words, if the attenuation bit is set, then the 10-bit ADC result is automatically multiplied by 3 to cal-
culate the actual voltage at that VMON input. Thus, the I
ing formula can always be used to calculate the actual voltage from the ADC code.
Voltage at the VMONx Pins
1
Note: ADC_VALUE_HIGH (8 bits), ADC_VALUE_LOW (4 bits) read from I
VMON = I
VMON10
VCCINP
VMON1
VMON2
VMON3
VDDA
2
C Readout Register (12 bits
(LA-ispPAC-POWR1014A Only)
From I
ADC
MUX
4
2
C ADC MUX Register
Programmable Analog
5
Attenuator
÷3 / ÷1
1
LA-ispPAC-POWR1014/A Automotive Family Data Sheet
1
, converted to decimal) * 2mV
2
C command, the ADC will be connected to the I
VREF- 2.048V
2
18
ADC
Internal
C readout register is 12 bits instead of 10 bits. The follow-
2
C/SMBUS interface (LA-ispPAC-POWR1014A only).
10
Digital Multiplier
Programmable
x3 / x1
2
C readout registers.
12
(LA-ispPAC-POWR1014A Only)
To I
2
C Readout Register
2
C bus (LA-isp-
2
C selected