MT16HTF25664AZ-1GAH1 Micron Technology Inc, MT16HTF25664AZ-1GAH1 Datasheet
MT16HTF25664AZ-1GAH1
Specifications of MT16HTF25664AZ-1GAH1
Related parts for MT16HTF25664AZ-1GAH1
MT16HTF25664AZ-1GAH1 Summary of contents
Page 1
... DDR2 SDRAM UDIMM MT16HTF25664AZ – 2GB MT16HTF51264AZ – 4GB Features • 240-pin, unbuffered dual in-line memory module • Fast data transfer rates: PC2-8500, PC2-6400, PC2-5300, PC2-4200, or PC2-3200 • 2GB (256 Meg x 64), 4GB (512 Meg x 64) • 1.8V DD DDQ • 1.7–3.6V DDSPD • ...
Page 2
... Table 3: Part Numbers and Timing Parameters – 2GB Modules 1 Base device: MT47H128M8, 1Gb DDR2 SDRAM Module 2 Part Number Density MT16HTF25664A(I)Z-1GA__ MT16HTF25664A(I)Z-80E__ MT16HTF25664A(I)Z-800__ MT16HTF25664A(I)Z-667__ Table 4: Part Numbers and Timing Parameters – 4GB Modules 1 Base device: MT47H256M8, 2Gb DDR2 SDRAM Module 2 Part Number Density MT16HTF51264A(I)Z-1GA__ MT16HTF51264A(I)Z-80E__ MT16HTF51264A(I)Z-800__ MT16HTF51264A(I)Z-667__ 1. The data sheet for the base device can be found on Micron’ ...
Page 3
Pin Assignments Table 5: Pin Assignments 240-Pin UDIMM Front Pin Symbol Pin Symbol Pin DQ19 61 REF DQ0 33 DQ24 63 4 DQ1 34 DQ25 ...
Page 4
... Pin Descriptions The pin description table below is a comprehensive list of all possible pins for all DDR2 modules. All pins listed may not be supported on this module. See Pin Assignments for information specific to this module. Table 6: Pin Descriptions Symbol Type Ax Input BAx Input ...
Page 5
Table 6: Pin Descriptions (Continued) Symbol Type SDA I/O RDQSx, Output RDQS#x Err_Out# Output (open drain Supply DD DDQ V Supply DDSPD V Supply REF V Supply SS – NC – NF – NU – RFU PDF: 09005aef80ed6fda ...
Page 6
Functional Block Diagram Figure 2: Functional Block Diagram S1# S0 DQS0 DQS0 DM0 DM DQ0 DQ DQ1 DQ DQ2 DQ DQ3 DQ DQ4 DQ DQ5 DQ DQ6 DQ DQ7 DQ DQS1# DQS1 DM1 DM DQ8 DQ ...
Page 7
... DRAM core and eight corresponding n-bit-wide, one-half-clock-cycle data trans- fers at the I/O pins. DDR2 modules use two sets of differential signals: DQS, DQS# to capture data and CK and CK# to capture commands, addresses, and control signals. Differential clocks and data strobes ensure exceptional noise immunity for these signals and provide precise crossing points to capture input signals ...
Page 8
Electrical Specifications Stresses greater than those listed may cause permanent damage to the module. This is a stress rating only, and functional operation of the module at these or any other condi- tions outside those indicated in the device data ...
Page 9
... Design Considerations Simulations Micron memory modules are designed to optimize signal integrity through carefully de- signed terminations, controlled board impedances, routing topologies, trace length matching, and decoupling. However, good signal integrity starts at the system level. Mi- cron encourages designers to simulate the signal characteristics of the system's memo- ry bus to ensure adequate signal integrity of the entire memory system ...
Page 10
I Specifications DD Table 9: DDR2 I Specifications and Conditions – 2GB DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating one ...
Page 11
Table 9: DDR2 I Specifications and Conditions – 2GB (Continued) DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 Meg x 8) com- ponent data sheet Parameter Operating bank interleave read ...
Page 12
Table 10: DDR2 I Specifications and Conditions – 4GB DD Values shown for MT47H256M8 DDR2 SDRAM only and are computed from values specified in the 2Gb (256 Meg x 8) com- ponent data sheet Parameter Operating one bank active-precharge current: ...
Page 13
Table 10: DDR2 I Specifications and Conditions – 4GB (Continued) DD Values shown for MT47H256M8 DDR2 SDRAM only and are computed from values specified in the 2Gb (256 Meg x 8) com- ponent data sheet Parameter Operating bank interleave read ...
Page 14
Serial Presence-Detect For the latest SPD data, refer to Micron's SPD page: www.micron.com/SPD. Table 11: SPD EEPROM Operating Conditions Parameter/Condition Supply voltage Input high voltage: logic 1; All inputs Input low voltage: logic 0; All inputs Output low voltage: I ...
Page 15
Module Dimensions Figure 3: 240-Pin DDR2 UDIMM 2.0 (0.079) R (4X 2.5 (0.098) D (2X) 2.3 (0.091) TYP Pin 1 2.2 (0.087) TYP 1.0 (0.039) 1.0 (0.039) TYP TYP 70.68 (2.78) TYP 45° (4X) U11 U12 3.05 (0.12) ...