ISPNANO S3 KIT Equinox Technologies, ISPNANO S3 KIT Datasheet - Page 74
ISPNANO S3 KIT
Manufacturer Part Number
ISPNANO S3 KIT
Description
ISP PORTABLE PROGRAMMER
Manufacturer
Equinox Technologies
Series
-r
Type
Portable ISPr
Datasheet
1.ISPNANO_S3_KIT.pdf
(134 pages)
Specifications of ISPNANO S3 KIT
Contents
Programmer, Cables, Power Supply
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
ATMEL AT90S, AT90CAN, AT90USB, ATtiny, ATmega, AT91SAM7xx, Zensys Z-Wave, 24xxx Serial EEPROM's
Other names
483-1022
ISPNANO S3 KIT
Q5595084
T1310537
ISPNANO S3 KIT
Q5595084
T1310537
- Current page: 74 of 134
- Download datasheet (9Mb)
1 Programmer Controlled
2 Programmer Controlled
3 Programmer controlled
4.2 Typical applications of each power supply
The table below gives an overview of the typical applications of the different ISPnano programmer
power supplies.….
# Power Supply
The following sections describe the various power supplies in more detail.
58
Target Vcc (TVCC)
Power Supply
Target Vpp (TVPP)
Power Supply
EXTERNAL VCC Switch
1.8 – 5.0
6.5 – 13.5
1.2 – 30.0
Voltage
(V DC)
range
ISPnano Series Programmer - User Manual – V1.11 – 12
Features / typical application of power supply
•
•
•
•
•
•
•
•
•
•
Used to power the internal
Driver Circuitry’
the
Used to apply controlled power to any Target System
(UUT) which can be powered at 1.8 to 5.0V.
Can also be used to power up the UUT at a specified
voltage for target testing and / or voltage calibration
purposes.
This power supply also features current / over-
current monitoring.
This power supply should only be used for devices
which require a
the device into
The voltage is defined by the programming
algorithm and is not user-definable.
Allows an ‘External power supply’ to be
switched under programmer control to a Target
System (UUT)
Typically used to power a UUT which requires
an input voltage of >5.0V
Can also be used if the ‘Target I/O Signal
Voltage’ needs to be different to the actual
‘Target Voltage’ e.g. an IC is powered at 3.3V
but the main UUT circuitry must be powered at
e.g. 5.0V.
Used to power the relay coils at +12V on the
‘ISPnano Series 3 ATE’ programmer
‘Programmer Target I/O’
‘programming mode’
‘Vpp’
which sets the signal levels for
programming voltage to force
‘Programmer Line
pins.
.
th
May 2011
Related parts for ISPNANO S3 KIT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ISP NANO RUN TIME LICENSE
Manufacturer:
Equinox Technologies
Part Number:
Description:
JTAG ISP UPGRADE FOR ATMEL AVR
Manufacturer:
Equinox Technologies
Part Number:
Description:
ISP PORTABLE PROGRAMMER USB
Manufacturer:
Equinox Technologies
Part Number:
Description:
CONVERTER KIT, COMMS, RS485
Manufacturer:
Equinox Technologies
Datasheet:
Part Number:
Description:
MOD PPM3 CONN-3 I/O ATMEGA JTAG
Manufacturer:
Equinox Technologies
Datasheet:
Part Number:
Description:
MODULE FOR PPM3-MK2 I/O DRIVER
Manufacturer:
Equinox Technologies
Datasheet:
Part Number:
Description:
MOD PPM3 SPECIAL FUNCTION DRIVER
Manufacturer:
Equinox Technologies
Part Number:
Description:
MODULE CONVERTER RS232 TO RS485
Manufacturer:
Equinox Technologies
Part Number:
Description:
MODULE CALCON FOR PPMS-MK2
Manufacturer:
Equinox Technologies
Datasheet:
Part Number:
Description:
ISP PORTABLE PROGRAMMER USB
Manufacturer:
Equinox Technologies
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies
Datasheet: