PA28F400BVB60 Intel, PA28F400BVB60 Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/3/336/intel_sml.jpg)
PA28F400BVB60
Manufacturer Part Number
PA28F400BVB60
Description
Manufacturer
Intel
Datasheet
1.PA28F400BVB60.pdf
(57 pages)
Specifications of PA28F400BVB60
Density
4Mb
Access Time (max)
60ns
Interface Type
Parallel
Boot Type
Bottom
Address Bus
19/18Bit
Operating Supply Voltage (typ)
3.3/5V
Operating Temp Range
0C to 70C
Package Type
SOP
Sync/async
Asynchronous
Operating Temperature Classification
Commercial
Operating Supply Voltage (min)
3/4.5V
Operating Supply Voltage (max)
3.6/5.5V
Word Size
8/16Bit
Number Of Words
512K/256K
Supply Current
65mA
Mounting
Surface Mount
Pin Count
44
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PA28F400BVB60
Manufacturer:
INTEL
Quantity:
45
Part Number:
PA28F400BVB60
Manufacturer:
INTEL
Quantity:
20 000
3.3.2.1
The WSM sets status bits 3 through 7 to “1,” and
clears bits 6 and 7 to “0,” but cannot clear status
bits 3 through 5 to “0.” Bits 3 through 5 can only be
cleared by the controlling CPU through the use of
the Clear Status Register (50H) command, because
these bits indicate various error conditions. By
allowing the system software to control the resetting
of these bits, several operations may be performed
(such as cumulatively programming several bytes
or erasing multiple blocks in sequence) before
reading the status register to determine if an error
occurred during that series. Clear the status register
before beginning another command or sequence.
Note, again, that a Read Array command must be
issued before data can be read from the memory or
intelligent identifier.
3.3.3
Programming
sequence. The Program Set-Up command is written
to the CUI followed by a second write which
specifies the address and data to be programmed.
The WSM will execute a sequence of internally
timed events to:
1. Program the desired bits of the addressed
2. Verify that the desired bits are sufficiently
Programming of the memory results in specific bits
within a byte or word being changed to a “0.”
If the user attempts to program “1”s, there will be no
change of the memory cell content and no error
occurs.
The status register indicates programming status:
while the program sequence is executing, bit 7 of
the status register is a “0.” The status register can
be polled by toggling either CE# or OE#. While
programming, the only valid command is Read
Status Register.
When programming is complete, the program status
bits should be checked. If the programming
operation was unsuccessful, bit 4 of the status
register is set to a “1” to indicate a Program Failure.
If bit 3 is set to a “1,” then V
acceptable limits, and the WSM did not execute the
programming sequence.
SEE NEW DESIGN RECOMMENDATIONS
memory word or byte.
programmed.
PROGRAM MODE
Clearing the Status Register
is
executed
using
PP
was not within
a
two-write
4-MBIT SmartVoltage BOOT BLOCK FAMILY
The status register should be cleared before
attempting the next operation. Any CUI instruction
can
however, reads from the memory array or intelligent
identifier cannot be accomplished until the CUI is
given the appropriate command.
3.3.4
To erase a block, write the Erase Set-Up and Erase
Confirm commands to the CUI, along with the
addresses identifying the block to be erased. These
addresses are latched internally when the Erase
Confirm command is issued. Block erasure results
in all bits within the block being set to “1.” Only one
block can be erased at a time.
The WSM will execute a sequence of internally
timed events to:
1. Program all bits within the block to “0.”
2. Verify that all bits within the block are
3. Erase all bits within the block to “1.”
4. Verify that all bits within the block are
While the erase sequence is executing, bit 7 of the
status register is a “0.”
When the status register indicates that erasure is
complete, check the erase status bit to verify that
the erase operation was successful. If the erase
operation was unsuccessful, bit 5 of the status
register will be set to a “1,” indicating an Erase
Failure. If V
the Erase Confirm command is issued, the WSM
will not execute an erase sequence; instead, bit 5 of
the status register is set to a “1” to indicate an
Erase Failure, and bit 3 is set to a “1” to identify that
V
Clear the status register before attempting the next
operation. Any CUI instruction can follow after
erasure is completed; however, reads from the
memory
identifier cannot be accomplished until the CUI is
given the Read Array command.
PP
sufficiently programmed to “0.”
sufficiently erased.
supply voltage was not within acceptable limits.
follow
array,
ERASE MODE
PP
after
was not within acceptable limits after
status
programming
register,
is
or
completed;
intelligent
21