A43L0616BV-7F AMIC, A43L0616BV-7F Datasheet - Page 16
![58T1324](/photos/40/61/406110/ge56tsop07-40_sml.jpg)
A43L0616BV-7F
Manufacturer Part Number
A43L0616BV-7F
Description
58T1324
Manufacturer
AMIC
Datasheet
1.A43L0616BV-7F.pdf
(48 pages)
Specifications of A43L0616BV-7F
Memory Type
SDRAM
Memory Configuration
1M X 16
Access Time
6ns
Interface Type
LVTTL
Memory Case Style
TSOPII
No. Of Pins
50
Operating Temperature Range
0°C To +70°C
Frequency
143MHz
Rohs Compliant
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
A43L0616BV-7F
Manufacturer:
AMIC
Quantity:
20 000
Device Operations (continued)
Auto Precharge
The precharge operation can also be performed by using
auto precharge. The SDRAM internally generates the timing
to satisfy t
and CAS latency. The auto precharge command is issued at
the same time as burst read or burst write by asserting high
on A10/AP. If burst read or burst write command is issued
with low on A10/AP, the bank is left active until a new
command is asserted. Once auto precharge command is
given, no new commands are possible to that particular bank
until the bank achieves idle state.
Both Banks Precharge
Both banks can be precharged at the same time by using
Precharge all command. Asserting low on
t
the end of tRP after performing precharge all, both banks are
in idle state.
Auto Refresh
The storage cells of SDRAM need to be refreshed every
32ms to maintain data. An auto refresh cycle accomplishes
refresh of a single row of storage cells. The internal counter
increments automatically on every auto refresh cycle to
refresh all the rows. An auto refresh command is issued by
asserting low on
both banks being in idle state and the device is not in power
down mode (CKE is high in the previous cycle). The time
required to complete the auto refresh
(February, 2008, Version 1.3)
WE
WE
RAS
(min) requirement, performs precharge on both banks. At
. The auto refresh command can only be asserted with
with high on A10/AP after both banks have satisfied
RAS
(min) and “t
CS
,
RAS
RP
” for the programmed burst length
and
CAS
with high on CKE and
CS
,
RAS
and
15
operation is specified by “t
clock cycles required can be calculated by driving “t
clock cycle time and then rounding up to the next higher
integer. The auto refresh command must be followed by
NOP’s until the auto refresh operation is completed. Both
banks will be in the idle state at the end of auto refresh
operation. The auto refresh is the preferred refresh mode
when the SDRAM is being used for normal data transactions.
The auto refresh cycle can be performed once in 15.6us or a
burst of 2048 auto refresh cycles once in 32ms.
Self Refresh
The self refresh is another refresh mode available in the
SDRAM. The self refresh is the preferred refresh mode for
data retention and low power operation of SDRAM. In self
refresh mode, the SDRAM disables the internal clock and all
the input buffers except CKE. The refresh addressing and
timing is internally generated to reduce power consumption.
The self refresh mode is entered from all banks idle state by
asserting low on
being low matters, all the other inputs including clock are
ignored to remain in the self refresh.
The self refresh is exited by restarting the external clock and
then asserting high on CKE. This must be followed by NOP’s
for a minimum time of “t
state to begin normal operation. If the system uses burst auto
refresh during normal operation, it is recommended to used
burst 2048 auto refresh cycles immediately after exiting self
refresh.
WE . Once the self refresh mode is entered, only CKE state
CS
,
RAS
RC
AMIC Technology, Corp.
RC
” before the SDRAM reaches idle
(min)”. The minimum number of
,
CAS
and CKE with high on
A43L0616B
RC
” with