ISL5416KI Intersil, ISL5416KI Datasheet - Page 32
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL5416KI
Manufacturer Part Number
ISL5416KI
Description
Up/Down Conv Mixer 1.8V 256-Pin BGA
Manufacturer
Intersil
Datasheet
1.ISL5416EVAL1.pdf
(71 pages)
Specifications of ISL5416KI
Package
256BGA
Operating Supply Voltage
1.8 V
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL5416KI
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL5416KIZ
Manufacturer:
INTERSIL
Quantity:
2
Part Number:
ISL5416KIZ
Manufacturer:
INTERSIL
Quantity:
20 000
In the tables below “reset state” indicates the register
contents after a HW reset or a SW hard reset. Unless
noted, a soft channel reset does not clear register
contents. A soft channel reset does clear the slave
registers of a master/slave pair (such as channel data
path control) but does not clear the master.
P(31:0)
27:25
24:21
31
30
29
28
20
19
18
17
16
15
14
13
12
ENABLE SERIAL OUTPUT.
1 = serial output mode is enabled. The DOUT parallel data bus is replaced with 4 serial output busses -- one per channel. See 0*06h
- 0*08h and Table 30.
RESERVED. Set to 0.
SCLK RESET.
1 = serial clock divider is reset by SYNCInX if the reset serial output bit is set in IWA = *000h, bits 13 or 29 of any of the 4 channels.
SCLK POLARITY.
1 = Low to High transitions at the center of the data bit.
0 = High to Low transitions at the center of the data bit.
SCLK RATE.
000 = SCLK DIsabled.
001 = input clock rate.
010 = input clock rate / 2.
011 = input clock rate / 4.
100 = input clock rate / 8.
101 = input clock rate /16.
RESERVED. Set to 0.
ROUTE CHANNEL 2 TO CHANNEL 3.
1 = route the output of FIR2 of channel 2 to the input of the CIC to FIR1 gain block in channel 3.
ROUTE CHANNEL 1 TO CHANNEL 2.
1 = route the output of FIR2 of channel 1 to the input of the CIC to FIR1 gain block in channel 2.
ROUTE CHANNEL 0 TO CHANNEL 1.
1 = route the output of FIR2 of channel 0 to the input of the CIC to FIR1 gain block in channel 1.
CHANNEL 0 EXTERNAL AGC SOURCE SELECT.
0 = when bit 14 is set, Channel 1 controls Channel 0 gain.
1 = when bit 14 is set, Channel 3 controls Channel 0 gain.
CHANNEL 2 EXTERNAL/INTERNAL GAIN CONTROL.
1 = Channel 2 gain is controlled by Channel 3.
CHANNEL 1 EXTERNAL/INTERNAL GAIN CONTROL.
1 = Channel 1 gain is controlled by Channel 3.
CHANNEL 0 EXTERNAL/INTERNAL GAIN CONTROL.
1 = Channel 0 gain is controlled by Channel 3 or Channel 1 depending on the state of bit 17.
CLKO2 OR INTRPT.
1 = CLKO2/INTRPT is INTRPT (2 clock period wide pulse).
0 = CLKO2/INTRPT is CLKO2.
NOTE: For INTRPT IWA = 0*0Ah, bit 31 must be set for the channel that is the interrupt source..
FSYNCX POLARITY.
0 = active high
1 = active low.
TABLE 15. COMMON OUTPUT CONTROL FUNCTIONS (GWA = 0000h) RESET STATE = 0x00000001h
32
Tables of Top Level Registers
ISL5416
FUNCTION
This register controls the output SYNC signal polarity, the
output clock rate and polarity, output data modes, and
channel cascading.