MAX3100CEE Maxim Integrated Products, MAX3100CEE Datasheet - Page 9

• Manufacturer Part Number: MAX3100CEE
• Description: IC UART SPI/MICRWIRE COMP 16QSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX3100CEE

• Features: Low Power
• Number Of Channels: 1, UART
• Fifo's: 8 Byte
• Protocol: RS232, RS485
• Voltage - Supply: 2.7 V ~ 5.5 V
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 16-SSOP (0.150", 3.90mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Table 5. Bit Descriptions
D0r–D7r
D0t–D7t
NAME
B0–B3
B0–B3
RAM
RAM
CTS
FEN
FEN
RTS
BIT
RM
RM
PM
PM
PE
PE
IR
IR
Pt
Pr
R
L
L
WRITE
READ/
w
w
w
w
w
w
w
w
w
w
w
r
r
r
r
r
r
r
r
r
r
r
r
_______________________________________________________________________________________
00000000
change
STATE
0000
0000
POR
No
X
0
0
0
0
0
0
X
X
0
0
0
0
0
0
0
0
0
0
Baud-Rate Divisor Select Bits. Sets the baud clock’s value (Table 6).
Baud-Rate Divisor Select Bits. Reads the 4-bit baud clock value assigned to these registers.
Clear-to-Send-Input. Records the state of the CTS pin (CTS bit = 0 implies CTS pin = logic
high).
Transmit-Buffer Register. Eight data bits written into the transmit-buffer register. D7t is ignored
when L = 1.
Eight data bits read from the receive FIFO or the receive register. These will be all 0s when
the receive FIFO or the receive registers are empty. When L = 1, D7r is always 0.
FIFO Enable. Enables the receive FIFO when FEN = 0. When FEN = 1, FIFO is disabled.
FIFO-Enable Readback. FEN’s state is read.
Enables the IrDA timing mode when IR = 1.
Reads the value of the IR bit.
Bit for setting the word length of the transmitted or received data. L = 0 results in 8-bit words
(9-bit words if PE = 1), see Figure 5. L = 1 results in 7-bit words (8-bit words if PE = 1).
Reads the value of the L bit.
Transmit-Parity Bit. This bit is treated as an extra bit that will be transmitted if PE = 1. To be
useful in 9-bit networks, the MAX3100 does not calculate parity. If PE = 0, then this bit (Pt) is
ignored in transmit mode (see the Nine-Bit Networks section).
Receive-Parity Bit. This bit is the extra bit received if PE = 1. Therefore, PE = 1 results in 9-bit
transmissions (L = 0). If PE = 0, then Pr is set to 0. Pr is stored in the FIFO with the receive
data (see the Nine-Bit Networks section).
Parity-Enable Bit. Appends the Pt bit to the transmitted data when PE = 1, and sends the Pt
bit as written. No parity bit is transmitted when PE = 0. With PE = 1, an extra bit is expected to
be received. This data is put into the Pr register. Pr = 0 when PE = 0. The MAX3100 does not
calculate parity.
Reads the value of the Parity-Enable bit.
Mask for Pr bit. IRQ is asserted if PM = 1 and Pr = 1 (Table 6).
Reads the value of the PM bit (Table 6).
Receive Bit or FIFO Not Empty Flag. R = 1 means new data is available to be read from the
receive register or FIFO.
Mask for R bit. IRQ is asserted if RM = 1 and R = 1 (Table 6).
Reads the value of the RM bit (Table 6).
Mask for RA/FE bit. IRQ is asserted if RAM = 1 and RA/FE = 1 (Table 6).
Reads the value of the RAM bit (Table 6).
Request-to-Send Bit. Controls the state of the RTS output. This bit is reset on power-up (RTS
bit = 0 sets the RTS pin = logic high).
SPI/MICROWIRE-Compatible
DESCRIPTION
UART in QSOP-16
9