SC16C650AIA44,529 NXP Semiconductors, SC16C650AIA44,529 Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
SC16C650AIA44,529
Manufacturer Part Number
SC16C650AIA44,529
Description
IC UART SINGLE W/FIFO 44-PLCC
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C650AIN40112.pdf
(50 pages)
Specifications of SC16C650AIA44,529
Features
False-start Bit Detection
Number Of Channels
1, UART
Fifo's
32 Byte
Voltage - Supply
2.5V, 3.3V, 5V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
44-LCC (J-Lead)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-3272-5
935270029529
SC16C650AIA44-S
935270029529
SC16C650AIA44-S
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C650AIA44,529
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
9397 750 11622
Product data
6.10 Loop-back mode
6.8 DMA operation
6.9 Sleep mode
The SC16C650A FIFO trigger level provides additional flexibility to the user for block
mode operation. The user can optionally operate the transmit and receive FIFOs in
the DMA mode (FCR[3]). The DMA mode affects the state of the RXRDY and TXRDY
output pins. Tables
Table 6:
Table 7:
The SC16C650A is designed to operate with low power consumption. A special sleep
mode is included to further reduce power consumption when the chip is not being
used. With EFR[4] and IER[4] enabled (set to a logic 1), the SC16C650A enters the
sleep mode, but resumes normal operation when a start bit is detected, a change of
state on any of the modem input pins RX, RI, CTS, DSR, DCD, or a transmit data is
provided by the user. If the sleep mode is enabled and the SC16C650A is awakened
by one of the conditions described above, it will return to the sleep mode
automatically after the last character is transmitted or read by the user. In any case,
the sleep mode will not be entered while an interrupt(s) is pending. The SC16C650A
will stay in the sleep mode of operation until it is disabled by setting IER[4] to a
logic 0.
The internal loop-back capability allows on-board diagnostics. In the loop-back mode,
the normal modem interface pins are disconnected and reconfigured for loop-back
internally. MCR[0-3] register bits are used for controlling loop-back diagnostic testing.
In the loop-back mode, OUT1 and OUT2 in the MCR register (bits 2-3) control the
modem RI and DCD inputs, respectively. MCR signals DTR and RTS (bits 0-1) are
used to control the modem CTS and DSR inputs, respectively. The transmitter output
(TX) and the receiver input (RX) are disconnected from their associated interface
pins, and instead are connected together internally (see
DCD, and RI are disconnected from their normal modem control input pins, and
instead are connected internally to DTR, RTS, OUT1 and OUT2. Loop-back test data
is entered into the transmit holding register via the user data bus interface, D0-D7.
The transmit UART serializes the data and passes the serial data to the receive
UART via the internal loop-back connection. The receive UART converts the serial
data back into parallel data that is then made available at the user data interface
D0-D7. The user optionally compares the received data to the initial transmitted data
for verifying error-free operation of the UART TX/RX circuits.
Non-DMA mode
1 = FIFO empty
0 = at least 1 byte in FIFO
Non-DMA mode
1 = at least 1 byte in FIFO
0 = FIFO empty
Effect of DMA mode on state of RXRDY pin
Effect of DMA mode on state of TXRDY pin
Rev. 04 — 20 June 2003
6
and
7
show this.
UART with 32-byte FIFO and IrDA encoder/decoder
DMA mode
0-to-1 transition when FIFO empties
1-to-0 transition when FIFO reaches trigger level,
or time-out occurs
DMA mode
0-to-1 transition when FIFO becomes full
1-to-0 transition when FIFO goes below trigger level
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
Figure
SC16C650A
7). The CTS, DSR,
15 of 50