TDA8552TS/N1,118 NXP Semiconductors, TDA8552TS/N1,118 Datasheet - Page 2

• Manufacturer Part Number: TDA8552TS/N1,118
• Description: IC AMP AUDIO PWR 1.4W AB 20SSOP
• Manufacturer: NXP Semiconductors
• Type: Class ABr

Specifications of TDA8552TS/N1,118

• Output Type: 2-Channel (Stereo)
• Package / Case: 20-SSOP
• Max Output Power X Channels @ Load: 1.4W x 2 @ 8 Ohm
• Voltage - Supply: 2.7 V ~ 5.5 V
• Features: Depop, Mute, Short-Circuit and Thermal Protection, Standby, Volume Control
• Mounting Type: Surface Mount
• Product: Class-AB
• Output Power: 1.4 W
• Available Set Gain: 30 dB
• Thd Plus Noise: 0.1 %, 0.04 %
• Operating Supply Voltage: 5 V
• Supply Current: 14 mA
• Maximum Power Dissipation: 1100 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 32 Ohms
• Input Signal Type: Single
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential, Single
• Supply Type: Single
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-3479-2; 935261316118; TDA8552TSDB-T

NXP Semiconductors
FEATURES
• One pin digital volume control (for each channel)
• Volume setting with up/down pulses
• Auto repeat function on volume setting
• Headphone sensing
• Maximum gain set by selection pin
• Low sensitivity for EMC radiation
• Internal feedback resistors
• Flexibility in use
• Few external components
• Low saturation voltage of output stage
• Standby mode controlled by CMOS compatible levels
• Low standby current
• No switch-on/switch-off plops
• High supply voltage ripple rejection
• Protected against electrostatic discharge
• Outputs short-circuit safe to ground, V
• Thermally protected.
APPLICATIONS
• Portable consumer products
• Notebook computers
• Communication equipment.
ORDERING INFORMATION
2002 Jan 04
TDA8552T
TDA8552TS
load
2 x 1.4 W BTL audio amplifiers with digital
volume control and headphone sensing
NUMBER
TYPE
SSOP20 plastic shrink small outline package; 20 leads; body width 4.4 mm
NAME
SO20
plastic small outline package; 20 leads; body width 7.5 mm
DD
and across the
DESCRIPTION
2
GENERAL DESCRIPTION
The TDA8552T is a two channel audio power amplifier that
provides an output power of 2 × 1.4 W into an 8 Ω load
using a 5 V power supply. The circuit contains two BTL
power amplifiers, two digital volume controls and
standby/mute logic. Volume and balance of the amplifiers
are controlled using two digital input pins which can be
driven by simple push-buttons or by a microcontroller.
Using the selection pin (GAINSEL) the maximum gain can
be set at 20 or 30 dB. The headphone sense input (HPS)
can be used to detect if a headphone is plugged into the
jack connector. If a headphone is plugged into the jack
connector the amplifier switches from the BTL to the SE
mode and the BTL loudspeakers are switched off. This
also results in a reduction of quiescent current
consumption.
The TDA8552T is contained in a 20-pin small outline
package. For the TDA8552TS, which is contained in a
20-pin very small outline package, the maximum output
power is limited by the maximum allowed ambient
temperature. More information can be found in Section
“Thermal design considerations”. The SO20 package has
the four corner leads connected to the die pad so that the
thermal behaviour can be improved by the PCB layout.
PACKAGE
TDA8552T; TDA8552TS
Product specification
SOT163-1
SOT266-1
VERSION