TDA7056A/N2,112 NXP Semiconductors, TDA7056A/N2,112 Datasheet - Page 9

• Manufacturer Part Number: TDA7056A/N2,112
• Description: IC AMP AUDIO 5.2W MONO AB 9SIL
• Manufacturer: NXP Semiconductors
• Type: Class ABr

Specifications of TDA7056A/N2,112

• Output Type: 1-Channel (Mono)
• Package / Case: 9-SIL (Straight Leads)
• Max Output Power X Channels @ Load: 5.2W x 1 @ 8 Ohm
• Voltage - Supply: 4.5 V ~ 18 V
• Features: Depop, Mute, Short-Circuit and Thermal Protection, Volume Control
• Mounting Type: Through Hole
• Product: Class-AB
• Output Power: 5.2 W
• Available Set Gain: 35.5 dB
• Thd Plus Noise: 0.3 %
• Operating Supply Voltage: 5 V, 9 V, 12 V
• Supply Current: 8 mA
• Maximum Power Dissipation: 9000 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 16 Ohms
• Input Signal Type: Single
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential
• Supply Type: Single
• Supply Voltage (max): 18 V
• Supply Voltage (min): 4.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-1141-5; 935054420112; TDA7056AU

NXP Semiconductors
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
DATA SHEET STATUS
Notes
1. Please consult the most recently issued document before initiating or completing a design.
2. The product status of device(s) described in this document may have changed since this document was published
DISCLAIMERS
Limited warranty and liability ⎯ Information in this
document is believed to be accurate and reliable.
However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to
the accuracy or completeness of such information and
shall have no liability for the consequences of use of such
information.
In no event shall NXP Semiconductors be liable for any
indirect, incidental, punitive, special or consequential
damages (including - without limitation - lost profits, lost
savings, business interruption, costs related to the
removal or replacement of any products or rework
charges) whether or not such damages are based on tort
July 1994
Objective data sheet
Preliminary data sheet
Product data sheet
3 W BTL mono audio output amplifier with
DC volume control
and may differ in case of multiple devices. The latest product status information is available on the Internet at
URL http://www.nxp.com.
DOCUMENT
STATUS
(1)
Development
Qualification
Production
PRODUCT
STATUS
(2)
This document contains data from the objective specification for product
development.
This document contains data from the preliminary specification.
This document contains the product specification.
9
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
(including negligence), warranty, breach of contract or any
other legal theory.
Notwithstanding any damages that customer might incur
for any reason whatsoever, NXP Semiconductors’
aggregate and cumulative liability towards customer for
the products described herein shall be limited in
accordance with the Terms and conditions of commercial
sale of NXP Semiconductors.
Right to make changes ⎯ NXP Semiconductors
reserves the right to make changes to information
published in this document, including without limitation
specifications and product descriptions, at any time and
without notice. This document supersedes and replaces all
information supplied prior to the publication hereof.
DEFINITION
Product specificiation
TDA7056A
stg max
). If the