RF2192 RF Micro Devices, RF2192 Datasheet
RF2192
Available stocks
Related parts for RF2192
RF2192 Summary of contents
Page 1
... Bipolar Transistor (HBT) process, and has been designed for use as the final RF amplifier in dual-mode 3V CDMA/AMPS and CDMA2000 handheld digital cellular equipment, spread-spectrum systems, and other applications in the 800MHz to 960MHz band. The RF2192 has a low power mode to extend battery life under low output power conditions. The device is packaged in a 16-pin, 4mmx4mm QFN. ...
Page 2
... RF2192 Absolute Maximum Ratings Parameter Supply Voltage (RF off) ≤31dBm) Supply Voltage (P OUT Mode Voltage (V ) MODE Control Voltage (V ) REG Input RF Power Operating Case Temperature Storage Temperature Parameter Min. Usable Frequency Range 400 High Power State- US-CDMA (V Low) MODE Frequency Range 824 Linear Gain ...
Page 3
... MHz 30 dB -33 dBc <-60 dBc 32 dBm 47 % 2:1 10:1 6:1 RF2192 Condition o Case T= =3.4V, V =2.85V. CC REG V =0V to 0.5V, Freq=824MHz to 849MHz MODE (unless otherwise specified) 2.5dB Backoff included in IS98D CCDF 1% 5.4dB Peak Average Ratio at CCDF 1% ACPR@885kHz ACPR@1.98MHz 4.5dB Peak Average Ratio at CCDF 1% ACPR@885kHz ACPR@1.98MHz ...
Page 4
... RF2192 Parameter Min. High Power State-CDMA450 (V Low) MODE Frequency Range 452 Linear Gain Second Harmonic Third Harmonic Maximum Linear Output Power 29 (CDMA Modulation) Total Linear Efficiency Adjacent Channel Power Rejection Input VSWR Output VSWR Low Power State-CDMA450 (V High) MODE Frequency Range ...
Page 5
... RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A9 DS080401 Interface Schematic and V need to be LOW (<0.5V). REG MODE is set LOW. When set MODE and V need to be LOW REG MODE See pin 10. RF2192 VCC1 100 From Bias GND1 Stages ...
Page 6
... RF2192 3.75 3.75 0. INDEX AREA 2 PLCS 12° MAX Dimensions in mm. Shaded pin is lead 1. 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com Package Drawing -B- 4.00 0. PLCS 2.00 0.80 TYP 1.50 SQ. 0.75 0.50 0.45 0.28 3.20 2 PLCS 1.00 C 0.90 0.05 0.75 0.00 0.65 0. PLCS A 2 1.60 2 PLCS 4 ...
Page 7
... High Q inductor (i.e., Coilcraft 0805HQ-series). **C1 and C14 are High Q capacitors 100 Ω Board 0 Ω CDMA (US) C26 4.7 μF Transmission Line Length C13 100 pF CDMA (US Ω RF2192 C2 4.7 uF C28 100 pF C17 L1* 2 100 OUT C1** C14** (i.e., Johanson C-series). ...
Page 8
... RF2192 4.7 μF 470 pF 1 100 510 Ω 100 Ω 100 pF 4.7 μF P2-1 P2-2 0 Ω 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com Application Schematic CDMA-450MHz Band P1-1 100 pF 4 ...
Page 9
... Evaluation Board Layout - US-CDMA Board Thickness 0.031”, Board Material FR-4, Multi-Layer, Ground Plane at 0.015” 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A9 DS080401 2.0” x 2.0” RF2192 ...
Page 10
... RF2192 PCB Surface Finish The PCB surface finish used for RFMD’s qualification process is electroless nickel, immersion gold. Typical thickness is 3μinch to 8μinch gold over 180μinch nickel. PCB Land Pattern Recommendation PCB land patterns are based on IPC-SM-782 standards when possible. The pad pattern shown has been developed and tested for optimized assembly at RFMD ...
Page 11
... Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A9 DS080401 A = 0.71 x 1.09 (mm) Typ 1.09 x 0.71 (mm) Typ 1.73 (mm) Sq. 3.20 Typ. 0.81 Typ. Pin 0.81 Typ 0.94 Typ 1.60 Typ. 1.73 Typ. RF2192 Dimensions in mm. 0.81 Typ. 1.60 Typ ...
Page 12
... RF2192 7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com Rev A9 DS080401 ...