AT90PWM316 Atmel Corporation, AT90PWM316 Datasheet - Page 294

no-image

AT90PWM316

Manufacturer Part Number
AT90PWM316
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of AT90PWM316

Flash (kbytes)
16 Kbytes
Pin Count
32
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
27
Ext Interrupts
4
Usb Speed
No
Usb Interface
No
Spi
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
10
Adc Speed (ksps)
125
Analog Comparators
3
Resistive Touch Screen
No
Dac Channels
1
Dac Resolution (bits)
10
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 105
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
5
Output Compare Channels
16
Input Capture Channels
1
Pwm Channels
12
32khz Rtc
No
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT90PWM316-16MU
Manufacturer:
SEAGATE
Quantity:
264
Part Number:
AT90PWM316-16MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT90PWM316-16MUR
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT90PWM316-16SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT90PWM316-16SUR
Manufacturer:
ATMEL
Quantity:
3 472
25.8.13
25.8.14
25.8.15
7710F–AVR–09/11
Reading the Signature Bytes
Reading the Calibration Byte
Parallel Programming Characteristics
Figure 25-6. Mapping Between BS1, BS2 and the Fuse and Lock Bits During Read
The algorithm for reading the Signature bytes is as follows (refer to
page 289
The algorithm for reading the Calibration byte is as follows (refer to
page 289
Figure 25-7. Parallel Programming Timing, Including some General Timing Requirements
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte (0x00 - 0x02).
3. Set OE to “0”, and BS1 to “0”. The selected Signature byte can now be read at DATA.
4. Set OE to “1”.
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte, 0x00.
3. Set OE to “0”, and BS1 to “1”. The Calibration byte can now be read at DATA.
4. Set OE to “1”.
(DATA, XA0/1, BS1, BS2)
for details on Command and Address loading):
for details on Command and Address loading):
Data & Contol
Extended Fuse Byte
Fuse Low Byte
RDY/BSY
Fuse High Byte
PAGEL
XTAL1
Lock Bits
WR
t
t
BVPH
DVXH
BS2
BS2
t
t
XHXL
PHPL
0
1
0
1
t
t
t
t
XLDX
XLWL
PLBX
PLWL
t
BVWL
BS1
t
WLWH
AT90PWM216/316
WLRL
0
1
“Programming the Flash” on
“Programming the Flash” on
t
WLBX
DATA
t
WLRH
294

Related parts for AT90PWM316